Who makes Sinkmaster garbage disposal?

Anaheim Manufacturing company produces the Sinkmaster garbage disposal, as well as a number of other kitchen appliances. The Sinkmasters come in a variety of styles and models, ranging from 1/3 horsepower to 1 horsepower in operating capacity.

What are the parts of a garbage disposal?

Main Components of a Garbage Disposal A garbage disposal is essentially a plastic or metal canister with a motor in the bottom and a large open compartment that catches food waste. Called a hopper or grinding chamber, the compartment has a spinning metal plate (sometimes called a flywheel) at its base.

How do you unclog a Sinkmaster garbage disposal?

To free the motor, insert either a disposer wrench or a ¼ inch Allen wrench into the bottom of the disposer and wiggle the motor back and forth until it moves freely. If the disposer does not have an opening at the bottom, insert a broom handle into the drain opening and try to wiggle the motor.

Can you replace the rubber on a garbage disposal?

A garbage disposal’s rubber splashguard, located inside the sink flange, prevents water and food from splashing up when the disposal is in use. The guard, or cover, may deteriorate due to normal wear and tear, and can be replaced.

How do you remove a bone crusher disposal?

How do you remove a bone crusher garbage disposal?

1. Turn off the electricity to the Sinkmaster garbage disposal by unplugging the unit from the outlet.
2. Position a bucket or large bowl underneath the Sinkmaster.
3. Use the Phillips screwdriver to remove the two screws that hold the drain outlet in place.

What is the top hole in a garbage disposal?

2. Upper hopper chamber – The top part of the cannister that holds food until it is chopped into small pieces.

Can you snake a garbage disposal?

If there is a garbage disposal installed, it will not be possible to feed the snake through the sink drain. However, if you have a double-sink, the garbage disposal is always only on one side; you may be able to get the snake through on the other side of the sink.

Can you plunge a garbage disposal?

If your kitchen sink isn’t draining and seems jammed, you can plunge it using a kitchen plunger to dislodge the debris that’s clogging your disposal.

How hard is it to change out a garbage disposal?

When you flip the switch to turn on the garbage disposal and all you get is a hum-or a loud, metal-on-metal grinding noise-you know something’s wrong. Fortunately, replacing a disposal isn’t hard, even if you haven’t done much plumbing.

How do you clean the black rubber on a garbage disposal?

How to Clean a Garbage Disposal Rubber Flange

1. Pour some hot water in the bowl.
2. Add a few drops of dish soap to form a foamy mixture and put on your dishwashing gloves.
3. Now, use the toothbrush and the soapy water to scrub the underside and top of the splash guard flaps.

What do you need to know about sinkmaster garbage disposer?

Flange, stopper, splash guard, and mounting hardware for the three bolt continuous feed. Garbage disposers are a great convenience for any kitchen, and Sinkmaster makes some of the best on the market. Depending on how often you use your appliance, you made need to perform repairs or maintenance on a regular basis.

Where can I buy parts for my garbage disposer?

PlumbingSupply.com ® is your best source on the Internet for repair parts for your garbage disposer. If you’re looking for new or parts for Waste King, Whirlaway, Sinkmaster or In-Sink-Erator disposers, or are looking for a new Kitchen-Aid or Waste Maid disposer, you have come to the right place.

Where can I get a waste King disposer?

If you’re looking for new or parts for Waste King, Whirlaway, Sinkmaster or In-Sink-Erator disposers, or are looking for a new Kitchen-Aid or Waste Maid disposer, you have come to the right place. Tired of reaching for the wall switch to turn on the disposer? Click here for an air-switch for easy disposer operation – easy to install, easier to use.