What does error code E64 mean on a Frigidaire dryer?

Heater Open Circuit
The error code E64 means Heater Open Circuit. This error appears when the Heating element or wiring to the heating element is defective.

How do you reset the code on a Frigidaire Affinity Dryer?

How to Retrieve the Error Codes in a Frigidaire Affinity Front…

1. Press and release any button on the dryer’s display panel to awaken it from idle mode.
2. Wait for 5 to 10 seconds then push and hold “Start/Pause” and “Cancel” at the same time.
3. Watch for the indicator lights on the control panel to flash.

What is E64?

E64 fault code on your home Electrolux clothes dryer. What this code stands for is that you have a shorted heating element. Other Possible fault: Heater thermostat faulty: Wiring faulty; Electronic board faulty. The only thing left at that point is to replaced the heating element and reset the machine.

Is it worth it to repair dryer?

Is it worth repairing a dryer? Dryer repairs are worth it if the appliance is less than 4 years old and the cost is less than $400. For older dryers and/or costly repairs, replacing your appliance is more cost effective.

Why is my Frigidaire dryer not drying?

A clogged dryer vent is one of the most common culprits behind any dryer not heating. If you have a dryer not drying clothes in a reasonable time, this could be why. Clean out the lint trap, and dryer duct located behind the dryer.

What does it mean when your dryer says call service?

If your Frigidaire Affinity dryer is beeping at you and giving you the “E64 CALL SERVICE” business, chances are you have a bad heating element. The good news is, with a screwdriver, a pair of pliers (a multimeter if you have one) and a new heater element you can fix this yourself and save a couple hundred bucks.

How much does it cost to have a heating element in dryer?

How Much Does a Heating Element Cost for a Dryer? A new heating element is usually between $40 and $100. This part might cost as low as $30 and as high as $200 or more, depending on the type of dryer.

Where is the thermal fuse on Frigidaire dryer?

The Frigidaire dryer thermal fuse location is in the back right corner of the dryer, attached to the heating element housing. Use a multimeter to check if the thermal fuse has continuity.

Where is the heating element located on a Frigidaire Affinity dryer?

The Frigidaire dryer heating element is on the inside of the back panel behind the dryer drum and is designed to provide the heat used to dry the clothes. The Frigidaire dryer heating element is set in a circular metal cage and can be replaced as a unit.

What is the Frigidaire dryer error code E64?

Frigidaire dryer error code e64 Thiss error code indicates an issue in the heating unit. It requires a complex action: you will have to disassemble the whole device and test every little part of the chainwork, which inclues thermostats, a thermistor, control board, etc.

How to fix a Frigidaire affinity E64 error?

A WORD OF CAUTION: You will be handling a lot of thin sheet metal components. Be careful as it is easy to cut yourself on them. First you’ll want to unplug the dryer and shut off the water source. Then disconnect the vent hose and the water feed (if applicable). Be sure and shut off the water valve first, or you’ll have a mess!

Why is there an error code on my Frigidaire affinity dryer?

Any error code in the E6* category will be related in some way to the heating circuit on Frigidaire dryers and Electrolux dryers. If your dryer is not heating or drying very well, or cutting off, you may see one of these error codes pop up.

What does the E68 mean on a Frigidaire dryer?

Frigidaire dryer error code e68 The E68 error code indicates a stuck button. Please, check each button in the console and find one that has gotten stuck. It will sway sideways a little.