How do you reset a paper shredder?

If your shredder cannot unjam itself, you will need to do this manually.

1. Unplug your shredder.
2. Remove the top shredding section.
3. Use a pair of tweezers to remove all jammed strands of paper from the blades.
4. Cut all curled pieces of paper.
5. If plastic is causing the jam, use a screwdriver to clear the block.

What could go wrong with a paper shredder?

Paper shredders are normally reliable devices, however, shredding paper can cause excessive levels of powder-like paper dust, debris and lint accumulating inside the shredder especially with paper shredders that cross-cut paper into fine particles.

What happens when a shredder overheats?

In Summary. Thankfully overheating a paper shredders motor is not all bad news, as a thermal overload sensor is what stops the motor when it reaches a pre-determined temperature range / duty cycle. Without a thermal overload sensor, the shredder will continue to operate until the motor is permanently damaged.

How do you fix a shredder that works in reverse?

With the shredder unplugged, you may use a set needle-nose pliers or tweezers to remove the blockage. Use the “Reverse” mode to back up and remove the stuck paper. The shredder will back up and loosen the jammed paper. If required, you may need to tug and remove several sheets to effectively clear the machine.

Why has my Fellowes shredder stopped working?

Pull the paper out manually if the switch-toggling fails to clear the jam. Oil the shredder if jams repeat. Move the power switch to the Auto position or the Forward position for five seconds if the shredder will only function in reverse. The shredder may be blocked and this will clear any blockage.

Is there a reset button on a Fellowes shredder?

b) The shredder may need to be reset. Switch it to the reverse (R) position for 2 seconds and then back to auto (I). This should reset it and it will operate again.

Why does my paper shredder only work in reverse?

Why does my paper shredder operate in reverse only? This likely has to do with the Auto run sensor of your shredder not being engaged correctly. When shredding small documents, such as checks or receipts, be sure that you are inserting the paper directly over this sensor.

How do I stop my shredder from overheating?

Schedule your shredding under this duty cycle amount. Occasional shredding in shorter bursts of time will keep the machine from overheating, compared to continuous operation which will cause the shredder to heat faster.

How do you fix a shredder that is overheating?

If you have been shredding papers for a long period of time or have been inserting large amounts of paper then your device may have overheated. Turn off your device and let it cool down for 30 minutes before attempting to use it again.

Why does my Fellowes shredder only work in reverse?

Where is the reverse button on Fellowes shredder?

The shredder should have a clearly marked “reverse” button or control switch depending on the machine. This is typically located on the top of the shredder.

Is the intimus 702 a high security Shredder?

The Intimus 702 SF is an NSA approved high security shredder that will meet all of your office’s document protection needs, as well as provide reliable and powerful performance.

How big is the intimus 45 CP7 Shredder?

And for those who need the best of all worlds—small size, quiet operation, fast speed, and high security—the 45 CP7 has it all in a footprint of only 1.9 square feet, and standing just over 2 feet tall. With intimus, you don’t have to compromise.

What to do if your Shredder does not work?

The shredder does not power on or work at all. 1. Make sure that the unit is securely plugged into a workingoutlet / socket. 2. If you have been continuously shredding for an extended period of time, the unit may have overheated and the thermal protection feature has been activated to shut off the machine.

What to do when paper is jammed in a shredder?

1. Turn shredder off. 2. Drizzle 2-3 tablespoons of oil onto the blades where the paper is jammed. 3. Let it soak for 30 minutes so the paper become saturated and softened. 4. Return the shredder back to the “Auto/On” mode. 5. If needed, forcibly insert a rigid sheet of cardboard to push the jammed paper through. 5.