How do I recover my Cisco router password?

Step-by-Step Procedure

1. Either switch off or shut down the router.
2. Remove the compact flash that is on the rear of the router.
3. Switch on the router.
4. Once the router is on Rommon mode, reinsert the compact flash.
5. Type confreg 0x2142 at the rommon 1> prompt in order to boot from Flash.
6. Type reset at the rommon 2> prompt.

How do I reset my Cisco 3800 router password?

Press Break on the terminal keyboard within 60 seconds of power up in order to put the router into ROMMON. If the break sequence does not work, refer to Standard Break Key Sequence Combinations During Password Recoveryfor other key combinations. Type confreg 0x2142 at the rommon 1> prompt in order to boot from Flash.

How do I reset my Cisco router username and password?

If your login details aren’t provided on the router itself, look for a physical reset button. Press and hold this button to return the router to its factory defaults. You should now be able to log in by leaving the Username field blank and entering “password” in the Password field.

How do I reset my router password if I forgot it?

If you can’t access the router’s web-based setup page or forgot the router’s password, you may reset the router to its default factory settings. To do this, press and hold the Reset button for 10 seconds. NOTE: Resetting your router to its default factory settings will also reset your router’s password.

What is the username and password of Cisco?

When you access the device, you should be asked to enter a username and password. The default user name of your Cisco router is either “admin” or “cisco”. The default password of all Cisco routers is either “admin”, “cisco” or is a blank field.

How do I restore from ROMmon mode?

You can recover the switch with the following steps:

1. You should already have a console connection to the Supervisor to see the previous output and perform the recovery.
2. The reboot continues until autoboot is prevented when you press Control-C and go into ROMmon mode.

How do I reset my Cisco 3800 router?

Reset Router to Default Configuration

1. With the router powered off, connect the power cord to your router, and plug the power cord into your power source.
2. Find the Reset button on the router.
3. Press and hold the Reset button while you power on the router.
4. Release the Reset button after 10 seconds.

How do you enter ROMmon mode?

To manually boot into the ROMmon mode, you will need to reboot the device and break the boot sequence. Pressing the Ctrl+Break key combination during boot usually does this.

What is default password for Cisco router?

admin
Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168. 1.1 or 192.168. 1.254.

How do I reset my Cisco AnyConnect password?

Connect to the VPN called “Cisco AnyConnect” on your device. Go to the password reset page at https://www.uwlax.edu/info/password-reset/ and change your password.

What is Netgear’s default password?

When you buy a new NETGEAR router, it is configured with factory default settings. When you use the local web address www.routerlogin.com to access your router’s web interface, the user name is admin and the default password is password.

How do I recover my WIFI username and password?

The default login username and password both are admin. If you or someone had changed them but you forget them now, the only way to access the modem/router is to reset the router to factory default settings. Note: If you reset the device, the device will return to factory defaults, you will lose all your settings.

When the router reboots it will load the old configuration with the new password. Save the password so that it will be persistent during reboots, type copy run start Reboot the router by typing reload at the enable prompt. Now, keep that password in a nice safe place – in your head does not count.

How can I recover my Cisco 3600 router?

If both routers are identical, or same series, you can use the Flash card from the other router in order to boot the one you want to recover. 3600/3700/3800 series routers run their Cisco IOS software from dynamic RAM (DRAM), so you can remove a PCMCIA card while the router runs.

How to do Password Recovery on a Cisco 6×00?

Important: To simulate step 4 on a Cisco 6×00 using NI-2, pull out and then replace the NI-2 card. Press Break on the terminal keyboard within 60 seconds of the power-up to put the router into ROMMON. If the break sequence doesn’t work, see Possible Key Combinations for Break Sequence During Password Recovery for other key combinations.

How can I recover Cisco IOS from another router?

If both routers are different but have a compatible PCMCIA Flash card filesystem, you can use the other router to load a Cisco IOS Software image into a Flash card, which you can then move to the router you try to recover. From the router that works, copy the image into the PCMCIA card.