Popular tips

How do I configure a Cisco 2960 switch?

by Rhyley Bryan

How do I configure a Cisco 2960 switch?

How to configure Cisco 2960 switch step by step?

  1. Interface the hosts to the switch and arrange them.
  2. Associate the switch to the switch and arrange the switch.
  3. Arrange the switch.
  4. Arrange the administration interface on VLAN 1.
  5. Check the design of the switch.
  6. Check availability utilizing ping and Telnet.

How do I change the configuration of a Cisco switch?

How to configure Cisco switch?

  1. Initial command prompt “Switch>” appears on the screen.
  2. Type “enable” next to it and press “Enter”.
  3. This will take you into the “EXEC” mode, also known as the Global Configuration mode.
  4. Go into configure mode using configure terminal.
  5. Enter the configuration commands one per line.

What is the default IP for Cisco 2960 switch?

10.0.0.1
The switch has a default IP address “10.0. 0.1” and a secondary IP address “10.0. 0.3”.

How do I configure an IP address on a Cisco 2960 switch?

Configure an IP address on a switch

  1. enter the VLAN 1 configuration mode with the interface vlan 1 global configuration command.
  2. assign an IP address with the ip address IP_ADDRESS SUBNET_MASK interface subcommand.
  3. enable the VLAN 1 interface with the no shutdown interface subcommand.

How do I reset a Cisco switch?

Hold the “mode” button on the front of the switch for 10 seconds. The lights will blink then go solid – the switch completely wipes all configuration and then reboots.

What is basic switch configuration?

Cisco Switch Configuration basic commands

  • Changing the hostname of a switch to GfgSwitch :
  • To add a banner message :
  • To set IP address in Switch :
  • To set the current clock time :
  • Apply password protection (enable password, secret password, console password and vty password) :

What are the steps to configure a switch?

  1. Step 1: Inspect your hardware. Check the model number of your shiny new switch.
  2. Step 2: Set up management IP.
  3. Step 3: Check VTP revision number.
  4. Step 4: Configure access ports.
  5. Step 5: Configure trunk ports.
  6. Step 6: Configure access ports.
  7. Step 7: Set up VTY line config.

How do I manage a Cisco switch?

How to Configure Cisco Switch: A Step-by-Step Guide with Commands

  1. Connect the Switch to PuTTY.
  2. Enter Privileged EXEC Mode and Set a Hostname for the Switch.
  3. Assign a Password to the Switch.
  4. Configure Telnet and Console Access Passwords.
  5. Configure IP Addresses With Telnet Access.

What is the default IP address for a Cisco switch?

192.168.1.254
The default IP address of the switch is 192.168. 1.254, which means you must choose an IP address that is not in use and between 192.168. 1.2 – 192.168. 1.253.

Do switches have IP addresses?

But since the switch does not have the capability to assign IP addresses, the computers connected to it will not be able to communicate with each other. They will get an Automatic Private IP Address (APIPA). You need to assign a static IP address to your computers.

How do I reset a Cisco 2960 switch?

Press and hold the front panel MODE button, and power-up the switch. – After a few seconds, the following should display. Release the MODE button.

How do I remove a configuration from a Cisco switch?

Clear the configuration of your switch

  1. Log on to your switch, and enter the privileged EXEC mode by entering enable and then entering the enable password command.
  2. Enter write erase, which erases the NVRAM file system and removes all files.
  3. At the prompt, confirm that you want to erase all files.

How do you set up a Cisco switch?

Configuring a Cisco 3548 switch is very simple. Connect the Cisco 3548 switch’s console port with the computer’s com port by using the UTP roll over cable. After physical connection, make a HyperTerminal session and give it any name. The com port setting should be Restore Default in the com port’s properties.

What is the purpose of a Cisco 2960?

They operate on Cisco IOS ® Software and support simple device management as well as network management. The Cisco Catalyst 2960-X and 2960-XR Series provide easy device onboarding, configuration, monitoring, and troubleshooting.

Does Cisco 2960x support WCCP?

According to the Cisco website, Cisco 2960X WS-C2960X-48TD-L doesn’t support WCCP, but 2960XR with IP base or IP services license does.

What is switch configuration?

Basic Switch Configuration (2.1) Switches are one of the most numerous devices installed onto the corporate network infrastructure. Configuring them can be fun and challenging. Knowing how switches normally boot and load an operating system is also important.