How do you clear a Miele fault code?

Press and hold the Program button until the “Intake/Drain” LED lights up. Then briefly press the Program button. To delete the fault code memory, press and hold the Program button until the “Intake/Drain” LED lights up. Then press and hold the Program button until the “SaniWash” LED goes out.

What does F12 mean on a Miele dishwasher?

Water intake
Miele Dishwasher Error Code = The display shows fault code F12 or F13 (Water intake). Cause Of Error/Fault Code = Stopcock is closed. How To Fix & Clear Error Code: 1 – Turn on the water supply at the stopcock. 2 – Water inlet filter is clogged.

What does F11 mean on Miele dishwasher?

Miele Dishwasher Error Code = Fault code F11 (Drainage) = Water not draining away.

How do I fix Miele waterproof fault?

Error Code: Waterproof Fault You can attempt to fix this error yourself, but you will need to first disconnect your washing machine and turn off the water supply. From there you will need to open the drum and remove any wet washing and then reset the error code.

How do I reset my Miele washing machine?

First, you should perform a general reset of the machine. Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians.

What is the stopcock on a Miele washing machine?

Your stopcock is the control tap for your mains water.

Does Miele dishwasher need salt?

All Miele dishwashers (except those in the Classic Series) come with a water softener system, which requires salt to operate. You can find salt and other Miele detergent, rinse aid, and cleaning products in our catalog.

Is there a reset button on a Miele dishwasher?

Press the On/Off button to Off, then back On. Most resets on Miele can be done by simply unplugging the washer for 5 or 10 seconds. This does not clear faults: it simply resets the CPU.

How do I reset my Miele dish?

Press and hold Start/Stop button until the red light blinks. 3. Press On/Off button to Off, then back On.

How do I fix my Miele f78?

Miele Dishwashers The circulation pump is blocked or has become dry and is stuck together. Remove the filter units and pour 1 litre of warm water and between 3 to 5 drops of rinse aid into the filter area and let it soak for 5 minutes. Run the programme again.

What is Miele WaterProof system?

The Miele dishwasher service manual states: The WaterProof System (WPS) consists of a number of interdependent safety features to provide protection against water leakage. 1. Protection against solenoid valve leakage: Each water intake is controlled by an inlet valve.

What does F24 mean on Miele dishwasher?

What does f24 mean on Miele dishwasher? F24-Heater relay problems like contacts that have fused together, moisture in this part of the dishwasher, or a problem with the plug on the heater relay’s exit point. F25-Desired temperature problem usually due to a faulty heater, heater relay, or too much detergent or rinse aid.

When to save a Miele fault code F51?

If, after a further check, the water level is still too high, then the program is interrupted, the fault code is saved and the drain pump is activated. Fault code F11 is also registered if heater relay 1K1 is not activated after the fault code F51 register check; see Section 080-3.18.

Is there a problem with my Miele dishwasher?

10,101 satisfied customers Dishwasher fault f24 have cleaned the waste/filter already. dishwasher fault f24 have cleaned the waste/filter already …  read more

How to check a Miele water intake fault?

1. Check the wires to the flow meter reed switch for continuity. 2. Check the plug connections. he program is interrupted and the drain pump is operated. The display shows the message Water intake fault F13. After approximately 2 to 4 minutes, the buzzer is activated for 2 minutes.