What is SAE J1926 1?

Rationale:SAE J1926-1 covers the requirements for inch O-Ring ports formerly covered in SAE J514. They have been moved out of SAE J514 for more flexibility when used with multiple connector systems. The design parameters are the same and remain unchanged except for conversion to metric dimensions and in some rounding.

What does BSPP Orr stand for?

ring Retaining Ring
• Easily adaptable to inch tube, metric tube and hose giving it worldwide acceptance. • Vast selection of port end options, including SAE Straight Thread O-ring Boss (ORB), NPTF, BSPP-ED, BSPP-O-ring Retaining Ring (ORR), BSPP, BSPT, ISO 6149, Metric-O-ring Retaining Ring (ORR), and Metric-ED.

What is a SAE #20 o-ring port?

LINCOLN, NE 68528. SAE O-Ring Fitting Guide. SAE O-ring (O-Ring Boss) are straight thread fittings that seal using a O-ring between the thread and the wrench flats of the fitting. The O-ring seals against the machined seat on the female port. O-ring fittings can be either adjustable or non-adjustable.

What is an orb fitting?

What are ORB Fittings? ORB, or (SAE Straight Thread O-ring Boss) fittings, incorporate a port connection as recommended by the National Fire Protection Association (N.F.P.A.) for leak prevention in medium and high pressure hydraulic systems. The male connection is a straight UNF thread with an O-ring.

What size is SAE 10?

SAE 45° Flare (SAE J512)

What is the SAE standard?

SAE International is a professional association and standards development organization for the engineering industry, with a special focus on transport sectors such as automotive, aerospace and commercial vehicles. SAE is most well known for its ratings of automobile horsepower and aerospace industry standards.

Will BSP fit into NPT?

NPT and BSP threads are generally not compatible due to the differences in their thread forms. NPT and BSP thread pitches (threads per inch, TPI) are listed below. You can use 1/2″ and 3/4″ NPT and BSP fittings together, but all others will be incompatible and will therefore leak.

Can you thread NPT to BSPP?

In most situations that don’t involve high pressure, a male NPT fitting can be threaded into a female BSPP fitting, using Teflon tape to seal. Note that because the male NPT fitting is tapered it will thread a little farther into the straight threaded BSPP female fitting.

What is a SAE 10 fitting size?

What does JIC stand for?

Joint Industry Council
JIC (or Joint Industry Council) fittings, defined by SAE J514, are compression fittings machined with a 37 degree flare seating surface and parallel threads. They are commonly manufactured in nickel alloys, brass, carbon & stainless steel. JIC Fitting hydraulic connections are common in most fluid power systems.

Are SAE and ORB the same?

O-Ring Boss: The threads of the SAE straight thread O-Ring Boss (ORB) and the straight thread 37⁰ JIC Flare are the same threads. The difference is the way each thread seals. While the JIC seals on a metal-to-metal flare, the ORB seals on an O-ring, which offers the best leak free connection.

What is a boss fitting?

Boss fittings are plumbing fittings used on o-ring boss systems (ORB), where the male parts are inserted into threaded female parts to provide a mechanical seal. Boss fittings are also recommended for hydraulic systems where leaks and failure are not tolerable.

What are the names of the SAE j1926 ports?

A fitting or port that follows SAE J1926 can go by many names, SAE-ORB, ORB, O-Ring Boss, Boss Stud, and SAE J1926 to name a few. All of these are common names for a hydraulic port connection that is manufactured per SAE J1926. In this post, we’ll just stick to calling it SAE J1926.

What’s the difference between SAE j1926-2 and J 1926-3?

There is a visible difference between the stud length of SAE J1926-2 and SAE J1926-3, as seen in Figure 1. This is why it is important to design your port depth based on SAE J1926-1 rather than designing it from the stud length of the fitting.

What’s the difference between ISO 11926 and SAE j1926-1?

SAE J1926-1 is SAE Straight Thread O-ring Port Conforms to MS16142. Does NOT conform to MS33649 (8). ISO 11926-1 is Connections for general use and fluid power — Ports and stud ends with ISO 725 threads and O-ring sealing — Part 1: Ports with O-ring seal in truncated housing SAE J1926-1 is the same to ISO 11926-1 standard.

What kind of pressure does the SAE j1926-3 stud Carry?

The SAE J1926-3 stud carries the working pressure of the L-series (light duty) ports, not the high duty port that is used with ORFS fittings. We’ve detailed what to look for on the port in our previous post: Leaking Ports?