What does F mean on Kenmore washer?

component problem
The F indicates that the washer control detected a component problem. If the F code was caused by excessive suds preventing the washer from draining, you may be able to shut the door and run a drain/spin cycle to remove the water from the washer.

How do I clear the error code on my Kenmore washer?

You will need to remove the power supply to the washer to reset the code.

1. Look for the “Pause/Cancel” button on the washer control panel.
2. Press the “Pause/Cancel” button twice to cancel the wash cycle.
3. Connect the water supply hoses back to the washer and turn on the water spigots.

How do I reprogram my Kenmore washer?

How to Reset a Kenmore Elite HE Washer

1. Press the “Stop” button twice, and then press the “Power” button.
2. Choose a wash cycle (e.g. “Normal”), and then choose your wash options (e.g. “Hot/Cold” or “Cold/Cold”).
3. Press the “Start” button to complete the reset process and restart the washing machine.

How do I fix error code f25 on my Kenmore washer?

My washer is getting an f 25 error code. On some models, the rear panel will have to be taken off for easier access to the motor control. Now with the washer-unplugged remove the each plug one at a time and make sure the pins in the connector are not bent then reseat them on the board. Now retest the washer.

What does IE mean on a Kenmore washing machine?

water inlet error
by Joseph Perez Earned 57,116 community points in Kenmore. February 7th, 2011. Answered in 10 minutes. On most LG washers the IE stands for a water inlet error. This means that the tub did not fill with water within a specific time frame.

What does F5 mean on my washing machine?

The F5 error code indicates that the Central Control Unit (main machine control board) detects a temperature sensor resistance that is out of the normal range.

Is there a reset button on Kenmore washer?

Plug the power cord into the wall outlet or turn the breaker back on and wait 30 seconds. Press the Pause / Cancel / Stop button twice to clear the display.

What is a F25 error code?

The F25 fault code indicates a problem with the drive motor home. The washer shuts down if the control can’t detect the speed of the motor.

How do I fix the F25 code on my Whirlpool washer?

Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). Plug in washer or reconnect power. Check the MCU by looking for operations of the drive motor. Check the drive motor for powered rotations.

What does IE mean in a washer?

An IE error code indicates that the washer was unable to fill with water. During cold and freezing weather conditions, an IE error code could mean the water in the water supply lines are frozen.

What does error code F50 mean on a Kenmore Oasis he washer?

Kenmore, Washers 1 Answer from this member: The F50 error code indicates that the machine control board senses that the drive motor has stalled. It is detecting no motor rpm’s from the rotor position sensor on the drive motor.

What does the F1 code mean on a Kenmore washer?

The F1 code indicates that the control board is defective. Try to reset the control board by unplugging the washer for 5 minutes. Plug it back in. This will sometimes fix the problem. If the F1 code returns after restoring power to the washer, replace the main electronic control board.

What to do if you get an error code on your Kenmore washer?

Press START. If code appears again, call for service. When all cycle indicator lights are blinking, see which status light is also illuminated and then check the list below for potential problem and troubleshooting checks, An error code may be shown in the Estimated Time Remaining display (on some models)

What does the F50 error code mean on a Honda Accord?

The F50 error code indicates that the machine control board senses that the drive motor has stalled. It is detecting no motor rpm’s from the rotor position sensor on the drive motor.