How do you reset a No Fault 6000 heater?

This is a PDR heater (power down reset). Simply power down the hot tub, wait 30 seconds and the heater will be reset. No more having to remove the cover too press the manual reset button like on the old heaters.

Is there a reset button on a hot tub heater?

A spa heater has a high-limit reset button. The spa’s pump and heater provide a soothing environment by circulating water through jets and increasing it to the bather’s desired temperature. A spa heater may need to be reset if it has tripped or stopped working.

How do you reset the thermal cut off on a hot springs spa?

How do you reset the heater on a Hot Springs Spa?

1. Locate the spa’s high-limit reset. This is a red button found on many spa packs.
2. Press the high-limit reset button.
3. Turn on your spa and observe its operation.
4. Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.

How do you bypass the pressure switch on a hot tub?

“Jumping Out” the pressure switch refers to placing a jumper wire between the two spade terminals or brass screws on the pressure switch. By connecting a wire between the two “in” and “out” terminals, you essentially bypass the switch itself.

Where is the high limit reset button?

The High Limit Reset Button is located behind the gas valve.

Why does my hot water heater keep tripping the reset button?

A short in one of the heating elements allows power to flow through the element even after the thermometer shuts off its power. This means the heating element is still working and will continue to increase the water temperature, eventually tripping the reset button.

Why my hot tub won’t heat up?

If your spa heater won’t heat, remove and clean the filter(s) to rule out a pressure or flow rate problem in your hot tub heater. Low water level, a clogged pump impeller, closed valves, clogged pipes, or blocked spa drain covers can also cause flow issues.

How do you test a Jacuzzi heater?

To test hot tub heating elements for integrity, use an ohm meter on its lowest setting. With the meter’s test leads, measure the resistance between the two element terminals. The acceptable resistance range for most heaters is between 9-12Ω (ohms), some may be as high as 20Ω.

Where is high limit switch on hot tub?

A limit switch will be located in your heater enclosure, mostly in its lower-left corner. It is usually white in color with a red button at the center. If your water is not heating up and you think the heater is the problem, one heater element that you need to check out will be the limit switch.

How do you troubleshoot a flow switch?

How to Troubleshoot Flow Switch Operation

1. Turn the unit off and unplug it from the power source for 30 seconds.
2. Ensure the flow switch valve is open.
3. Look at the water level in the hot tub.
4. Clean out the filter.
5. Check the output pressure and input pressure of the spa’s jets and filter.

How to replace Watkins no fault hot tub heater?

Replacement for Watkins No-Fault® heater for Hot Spring®,Tiger River®, Limelight spas. PDR auto reset. Included Bleed Tube Extension Kit for installation ease. You cannot buy a better quality spa heater at any price. Product notes: Molex connectors fit model year 2002 and newer.

What’s the rating of a Watkins no fault heater?

C-3564-1/C3564-1 Streamlined double-pass design Superior performance Manual reset Hi-Limit 1.5/6kW heater rating Nicolay heater element Threaded holes for sensors (sensors not included) Terminated wires on power cord 1-Year Manufacturer limited warranty. Would you like to tell us about a lower price?

Can you return a quicly no fault heater?

FYI, the merchant quicly agreed to take the heating unit back for a refund, so thumbs up to them. The return was not necessary, though, because the problem was not the heating unit, it was the heater circuit board. The new board installed quickly and easily, and the heating unit now works fine. If you buy one of these, buy with confidence.

Is there a warranty on a no fault hot tub heater?

Replaces obsolete No-Fault heaters with on-board pressure switch (a third grey wire). Also replaces trumpet-style Laing Infinity 7211. UL listed.1 year warranty.