Users' questions

How do I turn off my HP switch?

by Rhyley Bryan

How do I turn off my HP switch?

The most graceful way to shutdown an E-series Procurve switch is to do a “write memory” command at the CLI, (alternately exiting the menu interface or committing a change on the WebUI), wait for the command to complete, then pull the plug. If you want to reboot, you can do a “reload” or a “boot” command.

How do I put my HP switch into control mode?

Configuration commands and the context configuration modes

  1. HP Switch(config)# interface c3-c6. HP Switch(eth-C5-C8)#
  2. HP Switch(eth-C5-C8)# HP Switch(eth-Trk1)#
  3. HP Switch(config)# vlan 100. Command executed at configuration level to enter VLAN 100 context.
  4. HP Switch(vlan-100)#
  5. HP Switch(vlan-100)#?

How do I access my HP switch from command line?

When moving between interfaces, the switch retains the current privilege level (Manager or Operator). That is, if you are at the Operator level in the menu and select the Command Line Interface (CLI) option from the Main Menu, the CLI prompt appears at the Operator level.

How do I switch off ports in Aruba?

To disable contiguous ports use the – command. That will disable all ports from one to 20.

How do I restart my HP switch?

Solution

  1. Press the small, recessed Reset button on the face of the switch.
  2. Issue the command, reload from within the CLI.
  3. Or, issue the command, boot system flash to reboot into either primary or secondary flash.
  4. Or, unplug the switch for at least 10 seconds in order to cold boot the device.

How do I check my ports on my HP switch?

To check the mode setting for a port on the switch, use either the Port Status screen in the menu interface or show interfaces brief in the CLI (see Viewing port status and configuration (CLI)).

How do I check my HP switch settings?

To display the running configuration using the WebAgent:

  1. In the navigation pane, click Troubleshooting.
  2. Click Configuration Report.
  3. Use the right-side scroll bar to scroll through the configuration listing.

How do I log into my HP switch?

To enable web login, log in to the device via the console port, and perform the following configuration: • Enable HTTP or HTTPS service • Configure the IP address of the VLAN interface • Configure a username and password The device supports the following web login methods: • HTTP login: • HTTPS login: The following …

How do I enable ports in Aruba?

In the WebUI

  1. Navigate to the Configuration > Network > Ports window.
  2. In the Port Selection section, click the port you want to configure.
  3. For Port Mode select Trunk.
  4. To specify the native VLAN, select a VLAN from the Native VLAN drop-down list and click the <– arrow.

How do I know if my switch port is working?

You can view the summary or detailed information on the switch ports using the show interface status command. To see the summary information on all ports on the switch, enter the show interface status command with no arguments. Specify a particular module number to see information on the ports on that module only.

How do I reset a stack switch?

When the stack master is reset or powered off….

  1. Go to global configuration mode.
  2. Issue the command switch current-stack-member-number renumber new-stack-member-number.
  3. Return to the privileged EXEC mode and reload the member with the command reload slot current-stack-member-number.

Why is my no shutdown command not working?

09-07-2019 02:53 AM these is my command in router, which is connected to the switch 2960-24TT, the both interface is gigabitEthernet 0/1, but after I type the no shutdown command, the interface still down, how to fix it, what is the problem? And also all the interface of pc connected to the switch are down.

How do you shut down a HP networking switch?

Thank you for contacting HP Networking Support. The only way to completely shut down the switch is by pulling the power plug. This is by design. Since the switch can only be powered off through physical intervention, it negates the risk of someone inadvertently issuing a command to shut it down remotely.

How to enable no shutdown in Cisco switch?

“No Shutdown” Command – Enable Interface To enable an interface FastEthernet 0/1 on a CISCO switch or router, run: # enable # configure terminal (config)# interface FastEthernet 0/1 (config-subif)# no shutdown (config-subif)# end # write

Is there a way to shut down a power switch?

The only way to completely shut down the switch is by pulling the power plug. This is by design. Since the switch can only be powered off through physical intervention, it negates the risk of someone inadvertently issuing a command to shut it down remotely.