Users' questions

How do I reset my vigor?

How do I reset my vigor?

With the router powered on (ACT LED blinking), press the Factory Reset button with a pin, hold a few seconds until the ACT LED starts blinking rapidly, then release the button. After that, the router will restart with the default configuration.

How do I reset my vigor 2960?

How to reset the Vigor 3900 / 2960 to Factory Default settings

  1. Back up the existing configuration on the router if required – this is done from [System Maintenance] > [Configuration Backup] by clicking the Backup button.
  2. Press the Factory Reset button on the front of the router for 5 seconds.

How do I reset my DrayTek router password?

To change the router’s admin password, the process is similar for most models. Go to [System Maintenance] > [Admin Setting]. Enter the existing password in the Old Password box, then put the new password in both the New Password and Confirm Password boxes. Click OK to apply the change.

How do I set up DrayTek vigor?

Vigor VDSL2 Routers Access the DrayTek router’s web interface via your web browser, which will be accessible on http://192.168.1.1 by default. Enter the username of “admin” and the default password of “admin”. 2. Browse to [WAN] > [General Setup], click [WAN1] and set the VLAN Tag insertion (VDSL2) setting to Enable.

How do I reset DrayTek?

The quickest way to reset the router is to select ‘reboot’ from the web configurator, and click the button for ‘factory defaults’. On the 2200/2600 series, you can instead press the reset button the the back of the router and hold it until the left-hand LED starts to flicker rapidly, then release the button.

How do I reset my DrayTek modem?

Go to System Maintenance >> Reboot System on the web page. The following screen will appear. Choose Using factory default configuration and click OK. After few seconds, the router will reboot with all settings back to to the factory default.

How do I reset my DrayTek router?

How do I access my DrayTek router settings?

How to login my Vigor Router

  1. Connect a computer to one of the router’s LAN ports by an Ethernet cable.
  2. Make sure the network interface is using an IP in the 192.168.
  3. Open a browser on the computer.
  4. After logging in, you will access the management page of the router.

Does VDSL2 use PPPoE?

The VDSL2 modem acts as an ethernet bridge. On the DSL side, it operates in PTM mode and not ATM mode, hence PPPoE rather than PPPoA. The modem encapsulates the ethernet frames from the IP router with a control header for transmission over the twisted pair to the DSLAM in the cabinet.

How do I log into my DrayTek router?

The default username is “admin”, and by default password is “admin”. To find a newly installed DrayTek access point when it’s connected to the network of a DrayTek router, use the [External Devices] menu on the router, which will show any DrayTek devices detected on the network along with their IP address.

How do I Reset my vigor DrayTek router?

If you have physical access to the router, hold in the recessed Factory Reset button for 5 seconds, until the router’s ACT LED begins flashing rapidly. Release the button and the router will restart with its default configuration.

How to reset the Vigor 3900 / 2960 to factory?

The router will be accessible on http://192.168.1.1 with the default user account of ” admin ” which has a default password of ” admin “. A constant ping to 192.168.1.1 can be used to monitor whether the router is back online as that is the IP address that the router will be on after the factory reset procedure.

How to reset vigor router to factory default settings?

Log into the router’s web management page, and go to System Maintenance >> Reboot System. On the web page, choose “Using factory default configuration” and click Reboot Now.

What is the IP address of a vigor router?

In the address bar, enter 192.168.1.1 (which is router’s default LAN IP address). Hit Enter, and you will access the router’s login page. The default login username and password are both admin. (If you can’t open the login page, see Why can’t I access my Vigor Router? to troubleshoot)