What torque should lug nuts be at?

New wheels should be re-torqued after the first 50 to 100 driving miles.

What is the torque for RV lug nuts?

100 ft/lbs.
Lug nuts should be torqued to 100 ft/lbs. Always follow the appropriate star pattern as indicated in these instructions or in your axle manufacturer’s owner’s manual to assure proper torque.

How do I know what torque my wheels are?

Attach each lug nut by hand, and then use a manual torque wrench to tighten until you hear the ‘click’ sound that indicates you’ve reached the right amount of torque. The number—usually in the 75-100 lb-ft range—should be easy to locate in your vehicle’s owner’s manual.

What is the torque for 1/2 inch lug nuts?

to 85-ft-lbs
For a 1/2-inch lug the torque spec ranges from 75- to 85-ft-lbs.

How much torque does it take to remove a lug nut?

Car lug nuts are supposed to be torqued to about 100-120 ft lbs, but too often even the pros won’t take out a torque wrench, instead they’ll sow them on with an impact, set a lot higher than 100 ft lbs.

How many ft lbs should lug nuts be?

A quick glance at a lug nut torque chart shows that most lug nuts should be torqued between 80 and 100 ft-lbs. Some require less torque, others more.

How tight should 13/16 lug nuts be?

just about any steel wheel lug nut is a minimum of 85 lb. -ft. This includes a good majority of Lighter utility/cargo/boat trailers as well as alot of vehicles and light trucks.

What is the torque spec for aluminum wheels?

70 ft. lbs.
Aluminum wheels should have the lug nuts torqued to 70 ft. lbs. The beadlocks should be 20-22 ft.

How do you check torque?

Mark the tightened fastener and surrounding application. In the tightening direction, begin to slowly apply force to the tool until the first movement in the fastener is noted. The reading recorded is a good indication of the original torque applied to the joint. This is the best way to determine residual torque.

Should you use an impact wrench to tighten lug nuts?

With an impact gun, you aren’t applying any torque to the wheel, either. You are applying shock and inertia to the lug to get it to come off. Do not use the impact to tighten the lug nuts, though. It is very easy to over torque them.

Can torque wrench loosen bolts?

A torque wrench is a tightening tool. It is a very sensitive and precise tightening tool, and should never been used to loosen bolts.

Does oil drain plug need torque?

Most vehicles are equipped with a basic oil pan, and the basic oil drain bolt will require a little bit more torque. Torque the oil drain plug to 25 to 30 foot-pounds.

What are the torque specs for a Triumph Spitfire?

5/16 UNC x 5/8 setscrew Connecting rod bolt (Color dyed) 50 3/8 UNF x 1.65 bolt Connecting rod bolt (Phosphated) 46, 42-46 1147cc 3/8 UNF x 1.65 bolt Chainwheel to camshaft 24 5/16 UNF setscrew Crankshaft pulley nut 90-100 GT6, 150 for 1500 1 13/16″ nut Cylinder block water drain plug 35

How do you change wheel bearings on a Triumph Spitfire?

Put globs of new wheel bearing grease on my finger, and put it inside the hub until it was full around the inner circumference, to the point where it was somewhat “even” with the wheel bearing race – the part the wheel bearing rides against. Maybe a bit less. Empty in the center where the axle goes through and more.

Are there any examples of the Triumph Spitfire?

Wire wheels and a hard top were also available. An all-monocoque construction derivative of the Spitfire with pop-up headlamps, named the Triumph Fury, was proposed with a single prototype being built.

What kind of suspension do you use on a triumph?

Nylon suspension bushes Spitfire GT6 Herald Vitesse Grantura Vixen M Series Competition wheel stud and nut kit- stronger and longer TR7, TR8 and small Triumph with some modification Front suspension bolts Small Triumphs Adjustable radius arm Spitfire GT6 Herald Vitesse Anti roll bar drop links Small Triumphs

https://www.youtube.com/watch?v=vCm3A8nGpUs