What is water liquid ratio?

The water volume flow rate, relative to the total liquid volume flow rate (oil and water), at the pressure and temperature prevailing in that section.

How is LG calculated?

i) L (T1 – T2) = G (h2 – h1) L/G = (h2 – h1) / (T1 – T2) Where: L/G = liquid to gas mass flow ratio (kg/kg) T1 = hot water temperature (°C) T2 = cold-water temperature (°C) h2 = enthalpy of air-water vapor mixture at exhaust wet- bulb temperature (same units as above) h1 = enthalpy of air-water vapor mixture at inlet …

How to calculate water oil ratio?

Calculate Oil-Water Ratio from Retort Data

1. a) % oil in liquid phase = (% by volume oil x 100) ÷ (% by volume oil + % by volume water)
2. b) % water in liquid phase = (% by volume water x 100) ÷ (% by volume oil + % by volume water)

What is limiting liquid gas ratio?

It is common in wet scrubber terminology to express the liquid flow as a function of the gas flow rate that is being treated. This is commonly called the liquid-to-gas ratio (L/G ratio) and uses the units of gallons per 1,000 actual cubic feet or litres per cubic metre (L/m3).

How do you mix liquid ratios?

Divide 1 by the total number of parts (water + solution). For example, if your mix ratio is 8:1 or 8 parts water to 1 part solution, there are (8 + 1) or 9 parts. The mixing percentage is 11.1% (1 divided by 9).

What is cloud water mixing ratio?

The cloud-top cloud water mixing ratios vary from rc = 0.15 to 0.4 g kgА1, and show no trend with temperature.

How is LG ratio calculated?

Considering data from a heat and mass balance the dry air rate and the prevailing L/G ratio in the tower can be calculated: L/G = ha / [Cw x (tw2 – tw1)] = Cw = specific heat of water = 1.0.

How do you calculate LMIN?

Flow rate (L/min) = [Bucket Size (L)] ÷ [Fill time (sec)] × 60 × 0.8

1. 60 is to convert the unit to minutes.
2. 0.8 refers to a 20% reduction in flow rate to allow for pressure loss in your system. If the bucket test is taken off the main water feed at the correct pressure then this 20% allowance is not necessary.

What water cut means?

The water cut is the ratio of the water which is produced in a well compared to the volume of the total liquids produced. The water cut is the ratio of the water which is produced in a well compared to the volume of the total liquids produced.

What is meant by minimum liquid gas ratio?

The solute mole fraction is reduced to y2 at the outlet. By material balance for the solute in the gas, the amount to be removed is G ( y1 – y2 ). The least amount of liquid Lmin that can remove this amount of solute is the minimum liquid rate, often expressed in terms of a liquid-to-gas ratio, Lmin/G.

What is the transition from gas to liquid?

The process of a liquid becoming a gas is called boiling (or vapourization), while the process of a gas becoming a liquid is called condensation.

What is a 4 to 1 ratio?

Four to One ( 4:1 Mix Ratio ) If you were ordering a quart of Part A, this means you would need an 8 fl oz can ( a quarter quart ) of Part B. After mixing Part A and Part B together, you will have 1.25 quarts or 40 fluid ounces of material.

How to calculate the ratio of rice to water?

1 cup of that rice – 1 and 1/4 cups of water (1:1 + 1/4 cups that will evaporate) 2 cups of that rice – 2 and 1/4 cups of water 3 cups of that rice – 3 and 1/4 cups of water As you can see, we do not double or triple the ratios, once we know how much water will evaporate we use a 1:1 ratio + the extra.

Which is the correct definition of liquid ratio?

Liquid ratio is also termed as “Liquidity Ratio“, “Acid Test Ratio” or “Quick Ratio“. It is the ratio of liquid assets to current liabilities.

What is the ratio of lye to water?

Lye concentration is the grams (or ounces) of alkali contained in 100 grams (or ounces) of lye solution. Lye concentration of 33% means there are 33 grams of alkali in 100 grams of lye solution. Water makes up the rest of the 100 grams. In other words, the water weighs 100 – 33 = 67 grams.

What is the gas to liquid ratio in a well?

6.3.2 Feasibility charts Casing build-up pressure 350 psi Line or separator pressure 110 psi Well gas/liquid ratio (GLR) 8500 scf/bbl Well depth 8000 ft