What is the underside of eaves called?

Soffit
What Is a Soffit? Your roof by necessity, will often times extend over the walls of your home. This overhang can go by a few names, such as the house eaves or the rafters of your roof. The underside of this overhang, when given a finished appearance, is known as the soffit, which means “something fixed underneath”.

What is an eave trim?

Eave trim, also referred to as drip edge, is the first piece of trim that will be installed on your metal roof. This step by step installation article specifically covers eave trim installation for an exposed fastener panel such as: ⅞” Corrugated, R Panel/PBR Panel, and Western Rib/7.2 Panel.

What is the trim below the roof called?

Fascia
Fascia: Vertical roof trim located along the perimeter of a building, usually below the roof level, to cover the rafter tails at the eaves and to seal off the top of the siding along the rake; also called gutter boards.

Are eaves and soffits the same thing?

The underside of the eaves is referred to as the soffit. The difference between the two is that the underside of the soffit is the only part of the roof that overhangs the wall.

What is the difference between rake and eave?

An Eave is defined as the edge of the roof that overhangs the face of a wall. This is the portion of the roof that protrudes beyond the side of a house or building. In contrast, a Gable (or Rake) is the overhang of a building that occurs on the side that is topped by a gable roof.

What is the difference between soffit and eaves?

In the widest sense of the term, soffits can refer to the underside of almost anything that’s constructed, including arches and porches. To summarise, an eave is part of a roof system and a soffit is part of the eave. In simple terms, eaves and soffits are two different parts of the same structure.

Does a metal roof need a drip edge?

A drip edge is not needed for metal roofing. If you make sure to overhang your metal roofing at least an inch, the drip edge is not necessary at the eaves and rakes. If the metal roof is hanging over an inch, the water will be directed away from the fascia anyway if at a slant.

Is fascia the same as trim?

Trim is the material used to encase windows and doors, among other features, on a home’s exterior. Fascia is a horizontal or angled board that encloses the edge or face of the projecting eaves.

What is the difference between an eave and a rake?

Do I need ventilation in soffits?

The chosen method will be the one that best suits the property. Vented soffits or over fascia vents are not required on properties that were built prior to the Building Regulations coming into enforcement or those that were originally constructed without ventilation.

What is the purpose of eave trim on a roof?

Eave Trim (sometimes called Eave Drip) is designed to redirect rain run-off coming from the roof away from the perimeter of the roofing fascia. It is designed for both aesthetic appeal and for effective redirection of rain from the roof top to the ground below, protecting the fascia boards from moisture exposure.

What do you use to trim wood under eaves?

In some cases, the joint may be trimmed out with a thin piece of wood trim. The plywood is fastened to a ledger board on the exterior side of the house, and on another ledger on the fascia on the opposite side. The ledger board is nothing more than a horizontal piece of wood fastened to the side of the house and the back of the fascia.

Where does Valley trim go on a roof?

Gable or Rake Trim is attached to the sloping edges of roof gables to prevent wind-driven rain… Valley Trim lies under the edges of roof panels where different roof gables come together at an angle. Eave Trim (sometimes called Eave Drip) is designed to redirect rain run-off coming from the roof away from the perimeter of the roofing fascia.

Which is the best PVC trim for fascia and eaves?

For fascia and eaves, our 100% cellular PVC trim will help you get the details right. Our S4S, SurEdge and Precision Cut Trimboard, Crown Moulding, Drip Caps, Back Bands and Panel Moulds stand out, cut cleanly and finish meticulously. Plus, they’re moisture proof, resist mold and require near-zero maintenance. Creating the right look.