What does F06 mean on Indesit washing machine?

Door lock fault
F06 — Door lock fault. Issue: Washing Machines door cannot be opened or closed / when the door is closed the machine the programme will not start. Advice: If your washing machines door will not close, please check for any obstructions in the door lock.

How do I fix F06 error?

How to Fix F06 on a Whirlpool Duet

1. Touch “Pause/Cancel” twice to cancel the F06 error on the display.
2. Plug the power cord back in and select a new wash cycle.
3. Press “Pause/Cancel” twice again if the F06 error code resumes.

How do I reset my Indesit washing machine?

Indesit washing machine factory reset instructions are as follows:

1. Switch off the power and unplug the machine.
2. Turn on the machine using the on/off button.
3. Set the timer control to the zero position.
4. Plug the machine back in.
5. Switch on the power.
6. The display lights should now be flashing.

What does F06 mean?

drive motor tachometer error
The “F06” fault code indicates a drive motor tachometer error. This means the control is unable to properly detect motor speed and the machine will shut down.

Where is the reset button on an Indesit washing machine?

Try to unplug the washer from the outlet for 2-3 minutes, then right after press and hold the start button for 3 seconds. This should reset the controls and allow you to put the washer into a drain/spin cycle.

How do I fix Indesit F06 error?

Indesit error F06 The door won’t close properly: Check if there’s any laundry in the door. Put the laundry all the way in the drum. Close the door and restart the washing machine.

What does F06 error mean?

The “F06” fault code indicates a drive motor tachometer error. This means the control is unable to properly detect motor speed and the machine will shut down. It could also be the tachometer circuit in the motor or an intermittent internal component connection within the (MCU).

What is the problem with Indesit washing machine?

Indesit washing machine fault Code F05 for example signifies a waste pipe blockage or a pump issue. This means that the door may not open. Or if it does the water stays inside the drum. Your engineer will check for blockages in the pump filter, waste hose, and all plumbing under the sink.

Why are all my lights flashing on my Indesit washing machine?

Indesit washing machine flashing lights are designed to flash when there’s a specific fault. if the wash, rinse, and spin function lights are all flashing at the same time this indicates a potential obstruction in the drain or waste pipe. Worn carbon brushes can also cause this to happen.

How do I fix F06 error on Whirlpool dryer?

Whirlpool error F05, F06, F07, F08, or F09

1. Turn off the dryer and unplug it.
2. Open the door and take out your laundry.
3. Wait about one hour for the heat to dissipate.
4. Insert the connector into the socket.
5. Put your laundry back in the drum.
6. Restart the dryer cycle.

How do I fix F06 error on whirlpool dryer?

What does F05 mean on Hotpoint Indesit washing machine?

This procedure should also be the same for the Indesit F05 error code and Whirlpool F05 error code. On some Hotpoint washing machines the F05 error code means a faulty pressure switch but that wasn’t the case with our washing machine, it wasn’t draining.

Why does my Indesit door lock say F6?

Note: The links above are needed to help keep this site running, please consider using them. All my Indesit error codes show F6 as not used. If the door lock has a pneumatic air look preventing the door from opening when water is inside check for a blockage.

Why is my Indesit error code not used?

All my Indesit error codes show F6 as not used. If the door lock has a pneumatic air look preventing the door from opening when water is inside check for a blockage. They fell into disuse years back to cut prices and because a lot of machines use less water though.

What to do if Indesit washing machine does not work?

We offer fixed price Indesit Washing Machine Repairs in London. Some or all display / functions do not work on my washing machine. Please disconnect (unplug) the appliance from the mains supply for a minimum of 2 minutes. Reconnect supply, wait 30 seconds and try starting the machine again.