How wide is a Chevy Dana 44?

This Dana 44 uses 11″ drum brakes and the most common ratio is 3.73. The axles will interchange between the models and use a 5 on vehicles during that time period. Dana 44 axle tube diameter ranges from 2.5″ to 3″, while the Dana 60 axle tube diameter is 3.125″.

How strong is a Dana 44?

The 44 is roughly the same as a GM 8.5″ Corporate 10-bolt, same ring gear diameter and most bearing sizes, which has about 90%+ of the strength of a 12-bolt Car axle. Your Dana 44 will handle 500 hp no problem, and with an axle and spool upgrade w/girdle cover and tubes welded to the centersection will handle 700 hp+.

Can a Dana 44 handle 40s?

For a daily driver or a non wheeling rig, 44 and 40’s are fine.

How wide is a Wagoneer Dana 44?

Long Jeep Fan My 78 narrow track waggy front dana 44 was narrowed by 3.5″ and is now right around 56-56.5 inches wide which would put the stock width at 59.5-60″ I could go home and measure it for sure if you want.

What is a Dana 44 axle?

The Dana/Spicer Model 44 is an automotive axle manufactured by Dana Holding Corporation and is used extensively among automobile manufacturers and in the automotive aftermarket area as well. The Dana 44 has been manufactured as a beam axle and independent suspension for both front and rear axle setups.

Is Dana 44 a good axle?

At the same time, the Dana 44 is a great axle if you don’t need giant tires or big power. Most people don’t realize how heavy a Dana 60 is and how much unsprung weight affects handling. The Dana 44 is also a heavy axle, but it’s significantly lighter than a Dana 60.

Is a Dana 44 a 1 ton axle?

Yes, D60s are widely considered “one ton axles” but the fact of the matter is, they made many 3/4 ton trucks with D60 front axles and many 1 ton trucks with D44 front axles.

How big of tires can a Dana 44 handle?

36-inch
We often get asked how big a tire a Dana 44 can hold up to. That’s not an easy question to answer. Several factors, such as terrain, vehicle weight, driving style, and engine output, come into play. However, as a very general rule, a 36-inch tire is about the limit for a Dana 44.

Is Dana 44 better than 60?

Like we said above, the Dana 60 is the stronger axle. If you want to run big tires or big power you need a Dana 60 axle. The Dana 44 is also a heavy axle, but it’s significantly lighter than a Dana 60. The ring gear on the Dana 44 measures anywhere from 8.5 to 8.8 inches depending on the truck.

How do you narrow a Chevy Dana 44?

A common swap is tom narrow a Chevy Dana 44 to the size of an International Scout II or a Jeep Wagoneer. Start with the Chevy axle lengths 36.13″ and 18.31″ and subtract the length of the target axle shafts. In the case of the Scout II subtract 32.91″ and 14.78″ giving you a cut number of 3.22″ for the long side and 3.53″ for the short side.

When did the Dana 44 front axle come out?

In 1977.5 Ford’s new F-250 axle now started to appear. This new axle was a high pinion, reverse cut, 8-lug Dana 44. This axle for the F-250 Dana 44 is slightly different than the F-100 & F-150 offered in 1977.

What kind of brakes does a Dana 44 use?

Starting in 1972, the Dana 20 transfer case was used which has the rear output shaft centered, so the rear axle has the differential in the center. From 1972-1975 the Dana 44 was used with a 30 spline flanged axle shaft. This Dana 44 uses 11″ drum brakes and the most common ratio is 3.73.

What kind of wheel pattern does Jeep Dana 44 use?

The Dana 44 was standard in Wagoneers, full size Cherokees, and J series pickups. A wide track version was introduced for the Cherokee and Wagoneer in the 80s. The Cherokees and Wagoneers built from 1974 on use a 6 on 5.5″ wheel bolt pattern. Models built before 1974 used a 5 on 5.5″ wheel bolt pattern.