How do I reset DSC alarm to factory defaults?

Complete the following steps to perform a factory default on a DSC Impassa Alarm System:

1. Power down the system. Start by opening up the DSC Impassa System.
2. Apply the jumper. Connect a jumper between inputs IO1 and IO2.
3. Perform the default. Plug in the AC transformer to power the system back on.
4. Confirm the default.

How do I factory reset my DSC 1832?

Perform the following to default the main control panel:

1. Power down the system completely.
2. Connect a short (wire) between Zone 1 and PGM1 on the control panel (remove all other wires form these terminals).
3. Power up the control panel (AC power only) for 10 full seconds.

How do you clear the memory on a DSC alarm system?

To clear the memory, arm and disarm the system. Certain sensors (such as smoke detectors and glass break detectors) have to be reset after an alarm. To reset detectors, press and hold the RESET key () for 2 seconds. If a sensor fails to reset, it may still be detecting an alarm condition.

How do you clear the trouble light on a DSC alarm?

DSC Security System Trouble Light When a trouble is present the system trouble indicator light will illuminate and the keypad will beep every 10 seconds. To silence the trouble beep simply press the # key on the keypad. Now press *2 on your security keypad.

How do you clear a DSC alarm problem?

How do I disable my DSC alarm system?

How Do I Disarm My DSC Alarm System?

1. Disarm from the panel. To disarm from the panel, simply enter in a valid user code or the Master Code.
2. Disarm with a key fob. To disarm using a key fob simply press and hold the disarm button on a programmed key fob while within range of the system.
3. Disarm through Alarm.com.

How do you clear the memory on a DSC alarm?

What is my DSC master code?

The default master code is 1234. The master code is automatically assigned to user number 40. The master code is the first user code that comes programmed on the panel and it cannot be deleted, but it can and should be changed. The master code allows you to do quite a few things on the alarm system.

How do I bypass DSC zone?

How to Bypass a Zone on a DSC Power Series Security Alarm Panel

1. The System Must be disarmed prior to proceeding.
2. Press the * Key.
3. Press the 1 Key.
4. Use the > key to scroll to the zone you wish to bypass.
5. Press the * Key on the appropriate zone.
6. A “B” should appear next to the zone when the system is bypassed.

How to reset a DSc 1500 to factory settings?

Remove short from default pins and press 91 to remove the lockout. 3. Press 20, then 1500, then press # #.” This has a chance of clearing the lockout without wiping the rest of the programming, but usually it clears everything (only a small subset of later models would do the easy reset). I have couple more questions to ask. 1.

How many zones can a pk5500 keypad be used for?

The PK5500 keypad can be used on security systems with up to 64 zones. These keypads are compatible with the latest version of the folllowing DSC security systems: Specifications • Temperature range: -10°C to +55°C (14°F to 131°F) † Humidity (MAX): 93%R.H. † Plastic enclosure protection degree: IP30, IK04 † Voltage rating: 12VDCnominal

How to install the pk5500 v1.1 control panel?

PK5500 v1.1 Installation Instructions WARNING: Please refer to the System Installation Manual for information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. NOTE: These instructions shall be used in conjunction with the system Installation Manual of the Control Panel

Is there a master code for the DSC 1500 alarm?

I have a DSC 1500 alarm at home. I tried to change my passcode but I found out I do NOT have the master code/ installer code. I tried some standard codes (like 1234, 1500, 1550) but no luck.