How do I check my Daikin error code?

1. Hold the timer cancel button down for 5 seconds, with the remote controller set toward the indoor unit. 2. The temperature display on the remote controller changes to the error code display and a long beep notifies this indication change.

Why is my Daikin aircon blinking?

The mould proof/cleaning lamp (green) flashes. The mould proof/cleaning lamp flashes to indicate that the dust box needs cleaning. After cleaning the dust box, reset the lamp. (2) With the air conditioner in non-operation, press and hold the filter cleaning indicator (LED) reset button for about 2 seconds.

How do I fix error code H6 on Daikin?

Re: Daikin H6 error You could try switching the power off to the outdoor unit, wait 3 minutes and then turn it back on. You might be lucky and the system will reset itself. H6 is “compressor motor overcurrent sensor is abnormal.”

How do I fix error code L5 on Daikin?

Re: Daikin RXS35BVMB L5 error – how to proceed?

1. Disconnect all cables from the compressor except for the earth.
2. Ensure the compressor and the unit itself are properly earthed.
3. Make sure there is proper earth on the shell of the compressor.

Why isn’t my Daikin working?

When the remote of the Daikin air conditioner is not functioning, try resetting the Daikin controller or remote. On the remote of the air conditioner, look for the ‘On/Off’ button. Press the ‘On/Off’ button and hold it for 2 seconds before you release the same.

How do I fix my Daikin aircon blinking?

What Does It Mean: Daikin Blinking Lights?

1. You will need to have the original Daikin remote controller.
2. Hold down this ‘Cancel’ button for about 5 seconds until you hear a beep and the screen shows ’00’.

What is Daikin error code U4?

Daikin Aircon error code U4 Daikin error code U4 indicates a communication error. There are 2 possible causes to this error code. Firstly, the wires between the indoor and outdoor units are not connected properly. Secondly, any PCB inside the condenser unit may not be connected properly as well.

How do I reset my Daikin error code U4?

Here is how to reset Daikin error codes U4: Simply try to hard reset the unit for 30 seconds then turn off the outdoor unit (the steps may differ for your model so refer to your manual for correct hard resetting procedure).

What is L5 error?

Daikin AC Error Code = L5 Error Code Definition = Inverter overcurrent (DC output) What To Fix/Check/Replace = Defective compressor coil – Compressor startup failure – Defective inverter PCB. AWM is your one stop shop for everything machine tool.

Why is my Daikin aircon not working?

How do I reset my Daikin thermostat?

To reset your Daikin ENVi thermostat: From the Home screen, press MENU. Select Settings ▶ Reset. Choose the reset option that suits your needs.

What are the error codes for Daikin split AC?

Index: 1-Daikin Split AC Error Codes: 2- Daikin L Series AC Error Codes: Supposed Causes: Wrong models interconnected Defective indoor unit PCB Disconnection of connector Reduction of power supply voltage Supposed Causes: Short-circuited air Clogged air filter of the indoor unit Dust accumulation on the indoor heat exchanger

Why does my Daikin air conditioner keep pinging?

The refrigerant flows in the air conditioner even if the air conditioner is not working when the indoor units in other rooms are in operation. Pinging; Generated when the size of the air conditioner slightly expands or shrinks as a result of temperature changes. Is a breaker off or a fuse blown?

How to operate a Daikin room air conditioner?

DAIKIN ROOM AIR CONDITIONER OPERATION MANUAL Français Español DAIKIN ROOM AIR CONDITIONER OPERATION MANUAL MODELS FTXS30HVJU FTXS36HVJU FTXS30LVJU FTXS36LVJU English Français Español 00_CV_3P228444-4K.indd 1 3/26/2013 4:11:44 PM 1 English CONTENTS READ BEFORE OPERATION

Why is my Daikin power supply not working?

Supposed Causes: Wiring error Breaking of the connection wires between the indoor and outdoor units (wire No. 3) Defective outdoor unit PCB Defective indoor unit PCB Disturbed power supply waveform Supposed Causes: Wrong models interconnected Wrong wiring of connecting wires Wrong indoor unit PCB or outdoor unit PCB mounted