What is 3M 94 primer used for?

3M™ Tape Primer 94 can be used to improve the overall adhesion of tape, film and vinyl graphics to polyethylene, polypropylene, ABS, PET/PBT blends, concrete, wood, glass, metal and painted metal surfaces. Make sure your surface is clean and dry before applying a thin, uniform coat of 3M™ Tape Primer 94.

Can you vinyl wrap a car in primer?

No, the film will not adhere to auto repair fillers. An epoxy primer/sealer, OEM vehicle paint and/or clear coat must be applied over the auto repair filler and the finish must be allowed to cure for the period of time specified by the manufacturer before applying film.

How do you remove 3M Primer 94?

3M Primer 94 may be applied with brush or swab. It can also be applied with a pressurized flow gun, knurled roller or other similar type of application equipment. Clean up: 3M Primer 94 can be removed with acetone. Vigorous scrubbing may be required.

Does car wrap use adhesive?

Put most simply, vinyl car wrap is adhesive-backed plastic sheeting, but oh what we can do with a roll of plastic today!

How long does it take for 3M tape to cure?

After application, the bond strength will increase as the adhesive flows onto the surface. At room temperature, approximately 50% of the ultimate strength will be achieved after 20 minutes, 90% after 24 hours and 100% after 72 hours.

Can you wrap a car with paint chips?

If you install a car wrap over an area with paint chips, it can cause the vinyl film to stick to the scratches and dents. In order to steer clear of these problems, it’s essential that you look into fixing the paint chips before having a wrap installed on your car.

Can you wrap a spray painted car?

Bad paint jobs with excess paint can cause an ‘orange peel’ effect that will not be hidden by a vinyl wrap. We recommend professional paint repair and proper cure time before a wrap should be applied to a vehicle.

How do I remove 3M adhesion promoter?

3M adhesion promoter 06396 can be cleaned up with methylethyl ketone (MEK) or acetone solvents (be careful with solvents on plastics). Vigorous scrubbing may be required. To prevent cosmetic damage to visible surfaces, be sure to apply the pro- moter or any solvents only to areas that will be fully covered by the part.

What happens if you leave vinyl wrap on too long?

Leaving the wrap on too long. If you start to see your wrap change color, spot some hairline cracks or see other signs of wear and tear, it’s time to replace your wrap. If you wait too long, the vinyl will crack and heavy sun exposure can bake the material onto the surface of the vehicle.

What can 3M tape primer 94 be used for?

Cleans up with isopropyl alcohol 3M™ Tape Primer 94 can be used to improve the overall adhesion of tape, film and vinyl graphics to polyethylene, polypropylene, ABS, PET/PBT blends, concrete, wood, glass, metal and painted metal surfaces. Dries in Minutes for Efficient Use

How long does it take 3M primer 94 to dry?

Allow 3M primer 94 to dry thoroughly before applying tape. This is usually accomplished in 5 minutes at room temperature. Be sure the primed surface remains free from contaminants prior to applying the tape.

Do you need adhesive tape primer 94 for controltac?

ControlTac requires adhesive Tape Primer 94 because it has a very low tack adhesive. No such problem with Avery’s 1005 EZn or EZRS vinyl. EZRS, which is removable and slideable, allows you to position the vinyl just where you need it, including in deep grooves.

Do you need 3M tape primer 94 for Avery EZN?

If you’re using 3M ControlTac Comply, you’ll need some help to get it to stay stuck in deep grooves. That’s what Tape Primer 94 is for. But it isn’t needed if you’re using Avery EZn or EZRS, and isn’t recommended if you’re using Orajet vinyls of any kind.