How do I reset my Linksys WRT300N router?

Reset – There are two ways to reset the Linksys WRT300N to its factory defaults. Either press and hold the Reset button for approximately 10 seconds, or restore the defaults from the Administration > Factory Defaults screen in its web-based setup page. Power – The Power port is where you connect the power adapter.

How do I setup my Linksys router for the first time?

Insert the Linksys Connect Setup CD in your computer’s CD drive. Once a pop-up window appears, click on Set up your Linksys Router. If you do not see any, double-click on the Computer or My Computer icon on your Desktop. Look for the icon then double-click it.

How do I setup my Linksys wireless G router?

How to Set Up a Linksys WRT54G Wireless G Router

1. Step 1: Connect the Modem. Plug the Ethernet cable from your cable or DSL modem into the Internet port on the router.
2. Step 2: Connect Your Computers.
3. Step 3: Connect the Power.
4. Step 1: Log In.
5. Step 2: Open Wireless Settings.
6. Step 3: Name the Network.
7. Step 4: Set Up Security.

How do I setup my Linksys 2.4 GHz wireless router?

Click the Wireless tab.

1. Under the Basic Wireless Settings sub-tab, select Manual.
2. NOTE: Select either the 2.4 GHz or 5 GHz band.
3. For the Linksys Wi-Fi Routers, you may enable either the 2.4 GHz or 5 GHz band, or both by setting the Network Mode to your desired standard (i.e. Mixed, Wireless-N Only, etc.).

How do I configure a Cisco Packet Tracer wireless router?

1. Step 1: Connect the Internet interface of WRS2 to S1.
2. Step 2: Configure the Internet connection type.
3. Step 3: Configure the network setup.
4. Step 4: Configure wireless access and security.
5. Step 1: Configure PC3 for wireless connectivity.
6. Step 2: Verify PC3 wireless connectivity and IP addressing configuration.

Why won’t my Linksys router connect to the Internet?

The quickest and easiest workaround for most issues concerning Linksys routers is to powercycle the device. To do this, power OFF the router, unplug the power cord and wait for 10 seconds before plugging it back in. Low signal quality received from your wireless router. Outdated router firmware.

Why can’t I connect to my Linksys router?

To resolve this issue, you can reset your router to factory default settings, uninstall and reinstall the Linksys Connect Software on your main computer, then reconfigure your router’s settings through Linksys Connect. To learn how to reconfigure your router with Linksys Connect, click here.

How do I setup my Linksys router without a modem?

LINKSYS ROUTER SETUP WITHOUT MODEM

1. Connect your Linksys router to an electrical outlet using the power adapter or power cord.
2. Press thePower button on the Linksys router and wait until it becomes ready for the connection.
3. Connect the Linksys router to your PC using a standard Ethernet.

How can I access my router without an Ethernet cable?

If you don’t prefer a wired Ethernet connection or don’t have an Ethernet cable, you can connect your router to the computer using a wireless connection. Make sure that you have a wireless router to make the connection.

How do I manually connect to my router?

To request a connection to the router, enter the IP address in a web browser—http://192.168.1.1, for example. Make sure you’re using the correct IP address. Then reboot the router, disable the firewall, and reset the router to factory settings.

How do I setup my Linksys router without a computer?

How to set up a Wi-Fi router without a computer

1. 1) Plug in your router, and wait a minute or two for it to completely power up.
2. 2) Using your smartphone/tablet, turn on your Wi-Fi and connect to your router’s network.
3. 3) You will be prompted to provide a password.
4. 4) When connected, open your device’s browser.

How do I configure WLAN?

Use the WPA2 security mode as the example.

1. On the Navigation pane, click Configuration > Network > WLAN to visit the WLAN page.
2. Select the Enable checkbox and then click Apply.
3. Configure the following settings: SSID – test. WLAN Interface – Select wlan0/1 from the drop-down menu.
4. Click OK to save the configurations.

How to configure the Linksys Smart WiFi router?

Configure Wireless Bridging on the 2.4 GHz band of the Linksys Smart Wi-Fi Router. Since the 2.4 GHz frequency band was used for bridging, only clients connecting through Local Area Network (LAN) can connect to the router via Wireless Bridge Mode.

How to set up a Linksys router without a setup CD?

Setting up your Linksys Wi-Fi Router without a Setup CD. Step 1: Go to the Linksys Support Site . Enter the model number of your product in the Search field and click on it. QUICK TIP: If you don’t Step 2: Click on the DOWNLOADS / FIRMWARE button. Step 3: Select the Hardware version of your

How to configure the wireless bridge mode on Linksys?

Configuring the Wireless Bridge Mode on most Linksys Smart Wi-Fi Routers 1 Determine which frequency (2.4 GHz or 5 GHz) you are going to use to bridge the router. 2 Only one frequency can be used for Wireless Bridging. 3 Only the frequency not used for Wireless Bridging can be broadcasted for other clients to connect.

Where do I save the setup software for my Linksys router?

Select the Hardware version of your device. Locate the Setup Software for your computer and click Download. NOTE: When the End User License Agreement prompt appears, click the AGREE button. Save the Setup Software and select a location on your computer to save the file. It is recommended that you save the file to the computer’s Desktop.