Guidelines

How do I reset my Cisco ASA to factory settings?

by Rhyley Bryan

How do I reset my Cisco ASA to factory settings?

Solution

  1. Connect to the ASA via the console Cable.
  2. log in and go to configure terminal mode.
  3. Execute the following command “config factory-default”
  4. Press the space bar a few times to execute the commands.

How do I reset my Cisco ASA 5505 without a password?

  1. Step 1 Connect to the adaptive security appliance console port according to the instructions in “Accessing the Command-Line Interface” section.
  2. Step 2 Power off the adaptive security appliance, and then power it on.
  3. Step 3 After startup, press the Escape key when you are prompted to enter ROMMON mode.

How do I reset my Cisco ASA password?

Reset Password in Cisco ASA Firewall

  1. Step 1: Login to Cisco ASA device with console cable and reboot the device.
  2. Step 2: Press ‘ESC’ key or ‘BREAK’ key on the keyboard to break the boot process.
  3. Step 3: Now, here is the trick.
  4. Step 4: Reboot the device.
  5. Step 5: When the ASA is booted, it will not ask for password.

How do I change my Cisco ASA password?

To set the enable password on your Cisco ASA 5505:

  1. Get into the command line. I prefer using the console cable to directly connect.
  2. Hit enter a few times to get the prompt.
  3. Type ‘ena’ to enter enable mode.
  4. Type ‘config t’ .
  5. Type ‘enable password PaSsWoRd’ , replacing the second, ‘PaSsWoRd’ with desired password.

How do I restore my FTD to factory settings?

The command to reset a Cisco Firepower Threat Defense (FTD) appliance to factory defaults without completely re-imaging the device is configure manager delete. This will erase the entire configuration (firewall rules, data interfaces, routing etc).

What is the default password for Cisco ASA 5505?

The default username for your CISCO ASA 5505 is Cisco. The default password is Cisco.

What is the default Cisco username and password?

Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168. 1.1 or 192.168. 1.254.

How do I reset my Cisco ASA 5520 password?

How do I reset my Cisco ASA 5505 password?

To recover passwords, perform the following steps:

  1. Console into the ASA.
  2. Reboot the ASA.
  3. Press the escape key during reboot to enter ROMMON.
  4. Tell the firewall to ignore the startup config on next reload: rommon #1> confreg.

How do you wipe a firepower?

There are two ways to factory reset these Firepower 2100 units….Factory Reset Firepower 2100

  1. Connect to the console of the device.
  2. Power off the system and turn it back on.
  3. When the system is booting you have to go into ROMMON mode, to do that press ESC or CTRL+L to interrupt the boot process.

How do I update firepower 4110?

Upgrade FXOS on a Firepower 4100/9300 Chassis Using the CLI

  1. Plan your upgrade.
  2. Download the FXOS platform bundle software package to which you are upgrading.
  3. Back up your FXOS configuration.
  4. Collect the following information that you will need to download the software image to the Firepower 4100/9300 chassis:

How to reset Cisco ASA 5510 to factory defaults?

The default password is blank, so when the appliance prompts you for a password, simply press return: At the bottom of the output, you should see the Configuration Register settings: Configuration register is 0x41 (will be 0x1 at next reload) When the appliance reboots, it will have a basic factory default configuration, with a blank password.

What is the IP address of the Cisco ASA firewall?

The Cisco ASA has been reset to factory settings. DHCP is enabled on the cisco device, and it’s internal IP address is now 192.168.1.1! If you had an enable password set, you may need to enter that in the password box when you try to connect using the ASDM.

How to enable Cisco ASA 5506 without password?

Just press Enter key without any password because the device doesn’t come with any default password. I type in ciscoasa>enable but it asked for password. Since I don’t have password.

How to restore Cisco firewall to factory defaults?

If you can get into the ASDM, it is easier to Reset to Factory Defaults using the Cisco’s ASDM. If you forgot the enable password, Lawrence’s comment on this page might help. There is a button on the back of the device that says ‘Reset’. This button appears to be entirely for looks. I think will help you fix the problem as much as this button will: