Where do you nail an asphalt shingle?
Where do you nail an asphalt shingle?
Use 4 nails per shingle placed 6-1/8″ above the butt edge, 1″ and 13″ in from each end and 1/2″ above each cutout. Drive nails straight so that nail head is flush with, but not cutting into shingle surface.
Should you nail shingles?
Because the thickness, weight, and shape of shingles vary, manufacturer’s instructions vary slightly. But virtually all manufacturers agree that nails should be installed below the adhesive strip. To keep a warranty intact, follow the manufacturer’s nailing and installation instructions closely.
What type of nails should be used for applying asphalt roofing?
For asphalt roofing shingles, use galvanized nails. Galvanization adds a layer of zinc onto the steel that significantly inhibits rust and corrosion. There are two methods of galvanizing nails: hot‐dipped and electro‐galvanized.
How long should your nails be for shingles?
Fasteners for asphalt shingles shall be galvanized, stainless steel, aluminum or copper roofing nails, minimum 12-gage [0.105 inch (2.67 mm)] shank with a minimum 3/8-inch-diameter (9.5 mm) head, of a length to penetrate through the roofing materials and not less than 3/4 inch (19.1 mm) into the roof sheathing.
Which is better roofing nails or staples?
Staple guns are smaller and better balanced. Coil nail guns are literally fed with a coil of nails, and the holder for the nails makes the gun much bulkier. Staples are far less prone to jamming up in a gun than nails. Staples cost less money.
Do you have to remove plastic strip on shingles?
Because the cellophane strips have no effect on the performance of asphalt shingles, it’s fine to leave them in place as you install the shingles. In fact, the effort to remove them is unnecessary and just adds an extra step for the contractor.
What material are roofing nails coated with so they won’t rust?
Roofing nails tend to be galvanized, a process that makes stainless steel resistant to rust by coating it in a layer of zinc, which does not rust. Galvanization is very important when it comes to roofing nails, but even here you need to be careful because there are different types of galvanization.
What size nails should I use for roof sheathing?
Step 3: Fasten Roof Sheathing Panels Properly. Fasten panels with a minimum of 8d Common (0.131-inch by 2-1/2-inch) nails spaced a maximum of 6 inches on center at supported panel ends and edges. At intermediate supports, fasten panels 12 inches on center. In high-wind areas, more fasteners may be required.
Why do roofers use nails instead of screws?
Nails are often preferred for structural joining, including framing walls, because they are more flexible under pressure, whereas screws can snap. Nails are also called upon when securing plywood sheathing for exterior walls, installing hardwood floors, and attaching siding and roofing.
Can roofing nails be too long?
Nail length Roofing nails should be long enough to penetrate the roofing material and go 19 mm into OSB, solid wood, plywood or non-veneer wood decking, or through thickness of decking, whichever is less. Some situations allow nails with less penetration above exposed soffits if extra nails are used.
Can you use staples to install roofing felt?
Tack the roofing felt down with 1/4″ staples using an air compressor with a pneumatic stapler, a hammer-tacker, or a staple gun every 12 inches.
When did roofers stop using staples?
2003
While it used to be common practice to use staples to attach asphalt shingles to a roof, this has been a prohibited method of attachment in Minnesota since 2003. Today, staples are considered an inferior method of attaching shingles to a roof, but it’s easy to understand why roofers like staples.
What type of Nail would be best for roof shingle?
Correct Nails for Cedar Shingles. The ideal nail types for cedar shingle roofing projects include corrosion-resistant varieties like stainless steel and hot-dipped galvanized.
What kind of nails to use for asphalt shingles?
Nails used to secure asphalt shingles must be intended for the purpose. The preferred attachment nails are galvanized steel or corrosion-resistant roofing nails. Be sure to verify this against local building code requirements and recommendations from the manufacturer.
What length roofing nails to use?
Nails that are longer than six inches are called pikes and they are seldom used on roofs. The most commonly used roofing nails range from one to two inches in length. If you need bigger nails including pikes, you may need to place a special order at the hardware store. The one to two inch roofing nails are suitable for most types of roof shingles.
Is metal roof more expensive than asphalt shingels?
In most cases, metal roofing and installation is more expensive than asphalt. However, there are expensive architectural shingles that cost more than lower-cost metals like aluminum.