What is the composition makeup of 95 5 solder?

The Oatey 95/5 wire solder is a patented lead free alloy specifically formulated for lines carrying drinking water. Made with 95% tin and 5% antimony, it meets the “lead free” definition of the Safe Drinking Water Act. It can not be used on aluminum, and its melting range is from 450°F to 464°F.

What temperature does 95 5 solder melt at?

Oatey 95/5 Lead Free Plumbing Wire Solder

Is 95 5 solder allowed to be used in soldering refrigeration tubing?

95/5 Solder is commonly used for potable water applications, refrigeration lines and cooling equipment. 95/5 Solder complies with CA & VT lead content regulations. PRECAUTIONS Read all cautions and directions carefully before using this product. Apply flux with brush- do not apply with fingers.

What is the metal content of 50/50 solder?

COMMON APPLICATIONS Oatey Bar Solder is a general purpose alloy of 50% tin and 50% lead. 50/50 Bar Solder is most commonly used for copper drain piping, tin plating, seaming joints and sheet metal.

Does 95 5 solder contain lead?

DESCRIPTION: 95-5 tin/antimony solder is a low temperature lead-free solder with a narrow melting range. It is primarily used for copper plumbing tube but can be used for other general soldering applications.

What is the melting point of silver solder?

Silver Solder Melting Point When working with silver, the melting point for . 999 fine silver is 1761 degrees F and with sterling silver, it is 1640 degrees F. With solder, there are multiple flow points available because of the complexity of multi-step soldering.

Is silver solder good for plumbing?

Because soldered joints made with tin-antimony and tin-silver are stronger, plumbing systems installed using them can withstand higher pressures and temperatures than systems made with 50-50 tin-lead solder.

Does 60/40 solder contain lead?

Standard lead-based solderis made of tin and lead. When you see 60/40 or 63/37, it means 60% tin by weight, 40% lead. Either once of these alloys should be fine for typical small electronics soldering.

What temperature does 60 40 Melt?

188 °C
Alloys commonly used for electrical soldering are 60/40 Sn-Pb, which melts at 188 °C (370 °F), and 63/37 Sn-Pb used principally in electrical/electronic work.

What is the best solder for plumbing?

The Best Solder Is Safe Solder The new lead-free 95/5 solder, 95% tin 5% antimony, has a lower viscosity than 50/50. That means it flows more quickly when molten. It flows so quickly that it can flow right through the joint while it is being applied leaving a gap at the top of the joint.

When to use 95 / 5 tin antimony solder?

Tin-antimony solder well suited for applications where moderately elevated temperature is a factor. With higher electrical conductivity and high fluidity, 95/5 is recommended for lead free installation of small diameter, tight fitting connections. Not recommended for use on brass or HVAC connections.

What is the melting temperature of 95 / 5 solder?

The 95/5 solder has a narrow melting range, between 450 F and 464 F. Designed for use in electrical or electronic connections subject to peak temperatures of approximately 4000F and in sweating copper tube joints in refrigeration equipment.

What makes up 95% of silverbrite solder?

1 91% Tin (1) 2 95% Tin (3) 3 4% Antimony (1) 4 5% Antimony (3) 5 2% Silver (2) 6 3% Copper (2) 7 15% Silver (3) 8 5% Phosphorus (2) 9 5% Silver (1) 10 6% Phosphorus (2)

What kind of wire solder is used for plumbing?

An error occurred while retrieving sharing information. Please try again later. Oatey® 95/5 Lead Free Plumbing Wire Solder is a tin-antimony wire solder designed for use in plumbing applications where frequent and extreme temperature changes and vibrations occur.