How do I reset my Dlink camera to factory settings?

Push and hold a paperclip in the reset hole for 5 seconds, thenrelease it. The camera should be back to factory default settings.

How do I reset my Dlink DCS camera?

Step 1: Locate the reset pinhole on the bottom of the DCS-8000LH. Step 2: Press and hold the RESET button for 10 seconds and release. The LED should turn RED or go off and come back on. Allow about 1 minute for the camera to reboot.

How do I reset my DCS 8525LH?

RESET OF THE D-LINK DCS-8525LH HD CAMERA

1. You can locate the reset button on the camera.
2. Now you can take the paper clip and press the reset button for the few seconds.
3. After this, the user can see the lights start flashing.
4. Here you can release the reset button.
5. After this, the user can see the lights are now stable.

How do I reset my DCS 5222l?

To reset your camera, please use an unfolded paperclip to press and hold the RESET button for at least 8 seconds while your camera is plugged in.

Why can’t mydlink camera connect?

Issue: Step 1: Check the LED on your mydlink camera and ensure that it is GREEN. Step 3: Ensure that any firewalls you may have installed are configured to allow UDP connections. If you are unsure, temporarily disable any firewalls during the setup.

How do I reset my DCS 8600LH?

RESET OF D-LINK DCS-8600LH OUTDOOR CAMERA

1. Search the reset button on the camera.
2. Now hold the reset button with a paper clip for two seconds.
3. The lights are also flashing.
4. You can release the reset button.
5. Here the lights are also calm now.
6. Your camera is also in default settings.
7. You need to set up the camera again.

Where is the WPS button on mydlink camera?

Press and hold the WPS button on the side of the camera for three seconds. The blue WPS status LED above the button will blink. Step 2: Press the WPS button on your wireless router or access point within 60 seconds.

How do I factory reset my DCS 8010LH?

RESET OF D-LINK DCS-8010LH WIFI CAMERA

1. Search the reset button on the camera.
2. Now you can use the paperclip and push the reset button for two seconds.
3. Led lights are flashing.
4. Release the reset button of the camera.
5. Led lights are stable now.
6. Your camera is in default settings.
7. The user can again set up the camera.

How do I connect my camera without WPS?

How do I connect IP camera without WPS?

1. Place the camera next to your router and connect it to the router with the included network cable.
2. After some seconds a connection LED on the camera switches to green, which indicates that the camera is connected to the network.

Can a dcs-930l be controlled from a laptop?

The DCS-930L can be accessed remotely, and controlled from any PC/Notebook over your local network or through the Internet via a web browser. The simple installation and intuitive web-based interface offereasy integration with your Ethernet/Fast Ethernet or 802.11b/g/n wireless network.

What is the serial port on a D-Link dcs-930l?

PCB is marked A2, exterior case is marked “H/W Ver.: A3”. U12 is W29GL032CB7S, 4 MiB Flash memory. U9 is W9825G6JH, 32 MiB SDRAM. JP1 is a 4-pin connector or blank header serial console. Software settings for the serial port are 57600 8N1.

Is the dcs-933l B1 compatible with the 930l ROM?

933L has double RAM and FLASH. Official webpage says that it only has 32 MB ram, however boot log and “free” suggests that its at least double of that amount. The DCS-933L B1 is not compatible with the 930L rom, so don’t flash it (yet).

Which is internet browser does the dcs-930l support?

The DCS-930L is a stand-alone system with a built-in CPU, requiring no special hardware or software such as PC frame grabber cards. The DCS-930L supports both ActiveX mode for Internet Explorer and Java mode for other browsers such as Firefox® and Safari®. Supports a Variety of Platforms