How configure httpd-SSL conf?

II. Apache: Installing & Configuring Your SSL Certificate

1. Copy the certificate files to your server.
2. Find the Apache configuration file (httpd.
3. Identify the SSL block you need to configure.
4. Configure the block for the SSL-enabled site.
5. Test your Apache configuration file before restarting.

What is Httpd-SSL conf?

httpd-ssl.conf. # # This is the Apache server configuration file providing SSL support. # It contains the configuration directives to instruct the server how to. # serve pages over an https connection.

Where is Httpd-SSL conf?

conf or ssl. conf and may be located at /etc/httpd/, /etc/apache2/ or /etc/httpd/conf.

Which Apache Web server configuration file directive determines if SSL is enabled or not?

Configuration Directives for SSL. The directives in /etc/httpd/conf. d/ssl. conf file can be configured to enable secure Web communications using SSL and TLS.

How do I configure SSL?

An Internet Protocol (IP) address for your SSL certificate.

1. Copy the files into the default location on your server.
2. Install the certificate.
3. Import an SSL certificate from another server.
4. Set up the bindings.
5. Save the certificate and key file.
6. Configure httpd.
7. iptables.
8. Verify configuration syntax.

How do I enable httpd SSL?

Enable SSL (Apache)

1. Locate your Apache configuration file and open with a text editor. The name of your Apache configuration file depends on your system platform.
2. Verify/update Apache’s configuration file and save. Open your httpd.
3. Verify or update Apache’s SSL configuration file and save.

How do I know if Apache SSL is enabled?

Run the command:

1. on CentOS/RHEL-based distributions. # grep SSLProtocol /etc/httpd/conf.d/ssl.conf. SSLProtocol +TLSv1.2.
2. on Debian/Ubuntu-based distributions. # grep -ir SSLProtocol /etc/apache2/* /etc/apache2/mods-available/ssl.conf:SSLProtocol +TLSv1.2 +TLSv1.3. To enable/disable SSL/TLS protocols, see this KB article.

How SSL works step by step?

how SSL works

1. A browser attempts to connect to a web site secured with SSL.
2. The server sends the browser a copy of its SSL certificate.
3. The browser checks whether it trusts the SSL certificate.
4. The server sends back a digitally signed acknowledgement to start an SSL encrypted session.

How do I enable SSL on my server?

To do this, follow these steps:

1. From the Computer Management console, right-click the Web site on which you want to enforce SSL and select Properties.
2. Select the Web Site tab. In the Web Site Identification section, verify that the SSL Port field is populated with the numeric value 443.
3. Select Advanced.

Is SSL enabled Apache?

If you cannot locate the configuration file, see the Apache documentation for your operating system. Note: On CentOS 7, the file is called ssl. conf rather than httpd-ssl….Procedure.

Does not include an ID which matches the server name Apache?

In general the warning “server certificate does NOT include an ID which matches the server name” is a warning (not a fatal error) addressed at the system administrator that they most likely made a configuration error indicating that the wrong TLS server certificate has been set, or at least that Apache httpd can’t …

How do you SSL?

1. Step 1: Host with a dedicated IP address. In order to provide the best security, SSL certificates require your website to have its own dedicated IP address.
2. Step 2: Buy a Certificate.
3. Step 3: Activate the certificate.
4. Step 4: Install the certificate.
5. Step 5: Update your site to use HTTPS.

Where to find SSL configuration file in httpd?

The default location and name of the SSL configuration file is /etc/httpd/conf.d/ssl.conf If the SSL certificate was installed before, you will see the path of the currently used configuration file near the relevant domain name in the httpd -S output:

What to do with httpd.conf configuration file?

The httpd.conf file is well-commented and mostly self-explanatory. Changes to the main configuration files are only taken by Apache only if started/restarted.It stores information on various functions of the server, which can be edited by removing or adding a number sign “#” at the beginning of the line, thus setting values for each directive.

Where is the SSL conf file on my computer?

The ssl.conf file on my machine is located in the directory /etc/httpd/conf.d/ which I think is normal. However, what are the other directories the ssl.conf file can be in, depending on the distrubution?

How does mod ssl add itself to the httpd server?

When we install the mod_ssl package, the module adds itself to the httpd server, so it will load it on next startup. A self-signed certificate is generated by default, which is used to establish encrypted connection with the browser. Open a browser, and point it to the server over https: