What is the cost of 5 Marla house?

For a double-unit 5 marla house, the labourers would charge around PKR 390 per sq. ft., which would take the total amount to around PKR 770,250.

How much it will cost to build a house in Pakistan?

Normal finished will cost Rs. 1450 per square foot, whereas expensive or imported finishes will cost Rs. 1950 per square foot. The total construction cost to build a house is in the range from 2800 PKR to 5000 PKR per square foot.

How do I estimate the cost of building a house?

Total Cost = 9,00,000 Materials,

1. Cement = 16.4% = 1,47,600 Rs.
2. Sand = 12.3% = 1,10,700 Rs.
3. Aggregate = 7.4% = 66,600 Rs.
4. Steel = 24.6% = 2,21,400 Rs.
5. Finishers = 16.5% = 1,48,500 Rs. (Paint = 4.1% + Tiles = 8.0% + Bricks = 4.4%)
6. Fittings = 22.8% = 2,05,200 Rs.
7. Total Cost = 9,00,000 Rs. /

What is the minimum cost of construction per sq ft?

The average construction cost of a 1,000 sq ft home may vary from about Rs 1,300 per sq ft to Rs 5,000 per sq ft. Home construction cost depends on multiple factors including, civil cost and finishing cost; hence, it considerably varies across locations.

What is the cost of 3 Marla house in Pakistan?

For first floor, grey structure cost will be Rs 9 lacs (1500 per Square feet) and A quality finish will cost Rs 7 lacs 50 thousand (1250 per SF). The total cost of grey structure will be Rs 19 lacs 50 thousand and A quality finish will be Rs 16 lac 25 thousand.

How much is labor per sqft?

Labor Rates Per Square Foot Labor runs between $4 to $10 per square foot. In urban areas, expect to pay on the higher end of this range, perhaps a little above depending on demand. The size of the project will make a significant impact on the cost of installation.

How many bricks are there in 10 Marla house?

Approximately 60,000 bricks are required to build a 10-marla house. The entire grey structure, from foundation and the rooftop to the boundary wall, can be constructed with this many bricks.

What is the cost of RCC slab per sq ft?

RCC work rate per sqft :- To get a rough idea for the RCC work rate per sq ft, you can get a hint from this formula, however, in general, it is assumed that RCC work rate is 40 to 60 rupees per sq ft, the approx cost for rcc slab is around Rs180 to 200 per square foot, where the cost for steel, labour, shuttering and …

How is RCC construction cost calculated?

How much does it cost to build a 30×40 house?

Site Size: 30×40 site house construction cost (Ground + 1, 3 BHK) upto 1875 Sq. ft built up area.

How much does it cost to build a 3 Marla house?

For the construction of a 3 marla house around 1 ton of Sarya is required which is equal to 1000 kgs. At the rate of PKR 130 per ton sarya, the total cost will be around PKR 130,000.

How much does it cost to build a house in 5 Marla?

The construction cost of a 5 marla house also includes costs in developing water supply, sewerage, gas and drainage systems. All of this is called plumbing work. Approximately, PKR 115,000 is required for the plumbing of the house, including labour cost and materials.

How big is a Marla in square feet?

6 Marla House Plans, “Marla” is a traditional unit of area that was used in Pakistan, India,and Bangladesh. The marla was standardized under British rule to be equal to the square rod, or 272.25 square feet, 30.25 square yards, or 25.2929 square metres.

What kind of steel is needed for 5 Marla house?

During the construction of the grey structure of a 5 marla house, steel is also required at various stages, for example, while installing door frames. For the grey structure of this area, Chougat Steel of around PKR 60,000 is required. In addition, the house must have safety grills on windows as well as the main gate.

How big is a kanal house in Marla?

Similarly, the covered area of a 10 Marla house is usually around 4,355 square feet. Estimated Covered Area for 1 Kanal House: 9,000 sq.ft. The dimensions of a 1 kanal house are (50×90) square feet. 1 kanal of land has approximately 20 Marla in total and the covered area is 9,000 square feet.