How much power can a A833 handle?

An A833 23 spline 4-speed will be fine behind 400 hp.

What is an 833 transmission?

The A-833 was reconfigured as an overdrive transmission using an aluminum case in 1975 and was used in Chrysler cars and trucks for added fuel economy. The overdrive version of the transmission reduced the third gear ratio to . 73:1 to be used as the overdrive, and the 1:1 fourth gear became third.

How do I identify a 4-speed Mopar?

All factory (original equipment) Mopar/Hurst 4-speed shifter mechanisms can be identified by the four digit number on the reverse lever, which is the longest of the three.

How do you identify TorqueFlite 727?

You can easily identify an A-727 by its oddly shaped 14-bolt oil pan. The A-727 uses a paper fluid filter and has two transmission bands, one for reverse, and the other is a kickdown band. All shift ratios were 2.54:1 for first gear, 1.45:1 for second gear and 1.0:1 for third gear. Reverse gear is 2.21:1.

How do I identify my Chrysler transmission?

Open the driver’s side door and find the white card on the side of the door that is filled with small black lettering. This card contains specific details about the year the car was made, its transmission, engine specifications and other details. Underneath or beside the “TR” symbol will be a number code.

How do you identify Torqueflite 727?

How much horsepower can a 904 transmission handle?

As everyone has said, a properly built 904 will take that 360 without an issue.

What letter in the VIN is the transmission?

The Vehicle identification number is a 17-digit number where each of them has a unique meaning that is associated with the vehicle. The transmission of the vehicle is usually in between the fourth and the ninth digits-you would get to know the type of transmission of the vehicle.

How much horsepower can a TorqueFlite 727 handle?

600 hp
The 727 is a relatively simple piece when compared to other automatic transmissions, and its strength is a function of that simplicity. We’ve put stock TorqueFlite transmissions behind big-blocks pushing upwards of 600 hp and found they not only survive, but perform quite well.

Is a 727 transmission good?

When speaking of automatic transmissions, the Chrysler A-727 or TorqueFlite 8 units are not only easy to find because of their many years of use, but they are also very strong and can be used in many performance and non-Chrysler applications, as well.

Is the A-833 a 4 speed or 3 speed?

A simple flip of the gear lever on the side cover gives the driver the illusion of three normal speeds and a fourth that is overdrive. Editor’s note: Chrysler described the change as “an A-833 four-speed transmission, converted over to a three speed manual transmission with an overdrive gear ratio.”

What are the gear ratios on an A-833?

Premium Member A-833 Transmission Gear Ratios 1st 2nd 3rd 4th Coarse-spline V8 (1966-70) 2.65 1.93 1.39 1.00 Coarse-spline V8 (1971-74) 2.44 1.77 1.34 1.00 Road Race T/A; most 1971-74 fine spline 2.47 1.77 1.34 1.00 Overdrive (mid-1970s and newer) 3.09 1.67 1.00 0.73

Where are the casting numbers on a Mopar A-833?

Casting numbers to properly identify an A-833 can be found on either the front input bearing retainer (snout) or the extension housing/tailshaft. During 1968 production, a raised pad was added to the passenger side of the transmission with a series of numbers stamped into it.

When did the Mopar A-833 overdrive come out?

Aluminum-cased units were used on the A-833 overdrive version, which began in 1975. Because the cast-iron units were much more rugged, these are the most sought-after replacements for four-speed transmission conversions. The earliest A-833s that were produced from 1964-’65 used a ball-and-trunnion rear output to connect to the driveshaft.