What causes EPC light on Audi a4?

This indicates a fault within the traction, throttle pedal or cruise control systems. When the EPC light is on, it means that the car is experiencing some sort of malfunction within the systems controlled by the EPC. …

How do I fix the EPC on my Audi a4?

To reset this light, try the following: Turn on the ignition switch, slowly step on the gas pedal until it’s pressed to the floor, and while holding the pedal there, turn off the ignition. Keeping the pedal pressed to the floor, turn the ignition switch back on.

What causes EPC light on Audi?

The EPC light indicates an issue with a computerized system in your vehicle. It is exclusive to VW, Audi, Bentley, and other V.A.G cars.

Can low battery cause EPC light?

An EPC light is caused by a fault condition in the electronic throttle body, but again, voltage surges from jump starting or really low battery can cause all kinds of problems.

Can I drive my Audi with the EPC light on?

While you can continue to drive with the EPC warning light on, you run the risk of doing significant damage to the engine. To help prevent damage, the EPC’s limp-home mode might activate, making the vehicle sluggish as you seek help. The vehicle should be checked by a competent technician as soon as is possible.

Can you still drive with EPC light on?

While you can continue to drive with the EPC warning light on, you run the risk of doing significant damage to the engine. To help prevent damage, the EPC’s limp-home mode might activate, making the vehicle sluggish as you seek help. An OBDII scanner is the best way to discover the source of the EPC light problem.

How do I fix my EPC?

If you want to fix the EPC light yourself, you can try the following: first, start the car normally. Then, start the car for the second time and push the gas pedal to the floor when the engine starts. In some cases, this works. It is also a good idea to check the electrical connections on the throttle body.

How much does it cost to fix an EPC?

In the case of a glowing Electronic Power Control (also called the EPC), You will need to pay an average of $124 to $214 to fix it, but that is only if the throttle body is malfunctioning. It can most likely be resolved by simply resetting the light. The cost to fix an epc light on a vw jetta is about $200.

What do you do when your Audi EPC light comes on?

An EPC warning light could be an indicator of a minor problem or of very serious problems. Therefore, if the light comes on, immediately seek a safe place to have your vehicle serviced by a competent technician.

Is it OK to drive with EPC light on?

Can I drive with my EPC light on?

What causes an EPC light on an Audi?

The most common causes of an EPC light on your Audi or VW is a faulty throttle body, a faulty ABS sensor, ABS ring or a faulty brake pedal switch. Here is a more detailed list of possible causes of the EPC Light. Throttle body failure; Bad ABS Sensor – Common on newer VW Passats; Failed brake pedal switch – Common problem on Golf 4 & Fabia

What is the electronic power control on an Audi A4?

The Electronic Power Control ( EPC) is an alternative to the engine management light as seen above used on Audi cars. This circle in brackets symbol is a system that monitors the Audi Hold Assist function. Audi Hold Assist helps to keep the vehicle stationary whilst the engine is running. Example can be whilst stopping on a hill at traffic lights.

What causes EPC light to go out on Volkswagen Golf 4?

There are several different causes when it comes to the EPC light as mentioned before. The most common problem with Volkswagen cars when the problem appears is a faulty ABS Sensor or ABS Ring. Failed brake pedal switch – Common problem on Golf 4 & Fabia A failed brake pressure sensor (Inside the ABS Module)

What does it mean when your EPC light comes on?

A failed brake pressure sensor (Inside the ABS Module) The easiest and fastest way to find the problem when your EPC light appears is to read the trouble codes from your car with an OBD2 Scanner. When the EPC light is on, it means that there are one or several trouble codes stored in one of your control units.