What is DC01?

DC01 steel (1.0330 material) is a European standard cold-rolled quality low-carbon steel flat product for cold forming. In addition, this steel is also used under electrogalvanizing conditions. The designation of the steel is DC01+ZE (or 1.0330+ZE), and the standard is EN 10152.

What is DC04 material?

DC03 – This grade is suitable for forming requirements such as Deep drawing and difficult profiles suitable. DC04 – This quality is suitable for high deformation requirements. DC06 – This special deep drawing quality is suitable for the highest deformation requirements.

What is B10 steel?

B10 – COLD REDUCED. Page 1. 1. PROPERTIES. This is a range of cold rolled non-alloyed mild steel grades with guaranteed maximum yield and tensile strength, guaranteed minimum ductility (elongation at fracture) and good formability (n and r values).

What is CR4 steel?

CR4 stands for Cold reduced steel sheets. Making steel sheets and plates using this method results in a product with a smoother surface and a fine finish. This product Is used for a multitude of purposes including fuel tanks, tool boxes, drip pans, trailer siding, etc.

What is S235JR material?

Steel grade S235JR is a popular general construction and machine steel that is made in accordance with the EN 10025-2 standard. Classification: Non-alloy structural steel. Products: Semi-finished products, long products and sheet hot-rolled products, wire rod and forgings.

How many types of rebar are there?

A variety of rebar lengths and diameters are available, but there are only six common types of rebar: European (a carbon, manganese, silicon, etc. alloy); carbon steel (basic “black” rebar); galvanized; epoxy coated; glass-fiber-reinforced-polymer (GFRP); and stainless steel.

IS 513 D grade material properties?

Atomic % 0.15 1.40 0.019 0.007 CR1 is a commercial(ordinary) quality “O” grade as per Indian standard:513 2008 specifications. CR2 is a drawing quality “D” grade as per Indian standard: 513 2008 specifications. CR3 is a deep drawing Quality “DD” grade as per Indian standard: 513 2008 specifications.

What is ASTM a568?

Abstract. This specification covers the general requirements for carbon, structural, and high-strength, low alloy steel sheets in coils and cut lengths. The steel sheets shall be manufactured by hot-rolling, cold-rolling or temper rolling.

What is ASTM a924?

This specification covers the general requirements for steel sheet in coils and cut length, metallic-coated on continuous lines by the hot-dip process. This material is intended for applications requiring corrosion resistance. Product analysis and coating analysis shall also be done.

What is CRCA steel properties?

CRCA signifies, “cold rolled close annealed.” This implies after hot rolling and pickling. The steel is cold rolled to a decreased thickness, making it weak and not very valuable, followed by tempering in a shut climate of nitrogen or other non-oxidizing gases, which softens it back up while securing it.

What is s275jr steel?

S275 is an unalloyed low carbon mild steel grade supplied as hot rolled. As a low carbon steel specifications S275 provides low strength with good machinability and is suitable for welding.

What are the mechanical properties of DC01 steel?

EN 10139 – Cold rolled uncoated low carbon steel narrow strip. The table below lists DC01+ZE steel mechanical properties. Yield strength: When the thickness is ≤0.7 mm but >0.5 mm, the yield strength value should be increased by 20 MPa.

Do you supply this en DC01 chemical composition?

Our main peoducts of steel are many kinds of special steel, like tool steel, mould steel, alloy steel, alloy constructural steel, heat-resistant steel, high speed tool steel,spring steel and bearing steel , stainless steel and so on, which have formed 12 series and more than 350 varieties with n… Do you supply this EN DC01?

What are the mechanical properties of DC01 formed by drece method?

Table 2 prese nt the mechanic al properties (YS, UTS, A a nd HV) of DC01 in initial state and af ter DRECE proce ssing. has very significant influence on the strength properties (YS, UTS and HV) increasing. Actual results deformed grains. DRECE pass, from 40% to value approximately 19%.

Is the DC01 grade DC01 suitable for cold forming?

The non-alloy steel DC01 acc. to DIN EN 10130 is suitable for cold forming of simple profile forms and components. Mechanical foldings are possible for thicknesses of up to 1,5 mm. To freedom of stretcher lines applies a period of 3 months after provision of the products for surface type B.