Users' questions

How do I set a default route in Solaris 11?

by Rhyley Bryan

How do I set a default route in Solaris 11?

Creating Persistent (Static) Routes

  1. Use the route command with the –p option to persistently add a route: # route -p add default ip-address.
  2. Display the currently active routes on a system by using the netstat command with the following options: # netstat -rn.

How do I delete a default route in Solaris 11?

How to Change The Default Route or Gateway on Solaris

  1. Edit /etc/defaultrouter. -This configuration will apply after next reboot. [root@SolarisServer ~]# vi /etc/defaultrouter 192.168.2.1.
  2. Run the following command to delete and add the default route. -This will apply the configuration with immediate effect.

How do I change the default route?

Workaround 1: Manually add the default route for the Interface

  1. Click Start, click Run, type cmd in the Open box, and then click OK.
  2. Type route print, and then press ENTER to view the routing table.
  3. Type the following command, and then press ENTER route add 0.0.0.0 mask 0.0.0.0 gateway IP metric 30 if Interface number.

How do I change my IP address permanently in Solaris 11?

Configuring the IP address

  1. Step 1 : Set the NCP. We would set the NCP to DefaultFixed profile in order to configure the IP address manually.
  2. Step 2 : Check the link status. The command “dladm show-dev” does not work in Solaris 11.
  3. Step 3 : Create a new interface.
  4. Step 4 : Creating IP address.

How do I find the default gateway in Solaris 10?

Check the file /etc/hostname. bge0 , the configured IP address could be in there. By default the hostname is listed in that file and the name is looked up in /etc/inet/hosts . From the found entry, the IP address is used together with the corresponding netmask from /etc/inet/netmasks .

How do I change the hostname in Solaris 11?

How to change hostname in Solaris 11

  1. To list the current hostname (i.e. config/nodename property) :
  2. Change the hostname to geekserver by setting the property config/nodename to geekserver.
  3. Refresh and restart the system/identity:node service for the changes to take effect.
  4. Verify the changes.

How do I change the default route in Solaris?

route add default If you want the route to be persisted when you reboot the system, you will need to set the route in the /etc/defaultrouter file.

How do you delete IP address in Solaris 11?

How to Change and Configure Solaris 11 IP Address

  1. To change the IPv4 static IP address, use below prefix: ipadm delete-addr /v4.
  2. [Configure an interface with DHCP:
  3. Manually Configuring the Default Route for a System: route -p add default

What is the command for default route?

Use the ip default-gateway command when ip routing is disabled on a Cisco router. Use the ip default-network and ip route 0.0. 0.0 0.0. 0.0 commands to set the gateway of last resort on Cisco routers that have ip routing enabled.

How do you remove IP address in Solaris 11?

How do I change the broadcast address in Solaris 10?

For Solaris 10 11/06 and earlier releases only, modify the IP address in the /etc/inet/ipnodes file or equivalent ipnodes database. The first entry should contain the IP address of the primary network interface and the host name of the system. You can optionally add nicknames for the host name.

How to add a default route in Solaris?

To flush (remove) the routing table of all gateway entries, use the route flush command. To cause the routing table to flush before the remaining options are evaluated, use the flush option before using other options : To add a default static route using the /etc/defaultrouter file, add the default router IP address to the file /etc/defaultrouter.

Which is the default gateway in Solaris server?

The Default Gateway or the Default Router is the IP address (IPv4) to which all the traffic to any target destination (s) which does not have a route in the Routing Table of the server will be forwarded. This Default Gateway is maintained in the file This IP Address should be in the same network or the subnet as that of the server itself.

How to configure an IP in Solaris 10?

However, in Oracle Solaris 10, you configure an IP in a single step by using the ifconfig command. You use the route command to manually manipulate the network routing tables. The use of the –p option with the route command makes the changes persistent across reboots.

How to configure persistent network in Solaris 11?

Use the following commands for persistent network configuration in Oracle Solaris 11: 1 ipadm: Creates persistent configuration of interfaces, addresses, and TCP/IP properties. This command replaces the ifconfig command that is used in Oracle Solaris 10. 2 dladm: Manages datalink configuration. 3 route: Configures persistent routes.