Why is my petsafe collar blinking green?

The receiver collar will emit a unique double tone as the contact points touch your pet’s skin. You will know that you have the proper fit when you hear the receiver collar emit the double tone and it flashes green 5 consecutive times.

Why is my petsafe collar beeping but not shocking?

My receiver collar is beeping but my pet is not responding to the static correction. Remove the collar from your pet. Make sure the static correction level on the receiver collar is set at 2 or above. Take the test light tool and place it on the receiver collar and walk out to the boundary of the containment system.

How do I change the settings on my petsafe collar?

With the Receiver Collar turned on, press and release the Mode Button briefly. When released, the unit will flash indicating the Correction Level by the number of times the indicator flashes. Press the mode button again within 5 seconds of the last red flash and it will increase one level.

Why is my petsafe collar not working?

Take battery out of the collar for several minutes and replace it with new battery. Make sure battery is installed properly. Make sure the tab within the battery housing unit is making good contact. If receiver collar still does not activate – remove a wire from the transmitter, try to change the levels.

How do you test a PetSafe collar?

The Test Light Tool is used to tell if your collar is working properly. Hold the tool against the contact points and activate the collar. For a remote trainer, activate the correction using the transmitter. For a fence, move the collar near the boundary, holding the collar at your dog’s neck height.

How do I know if my shock collar is working?

Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.

How do I know if my petsafe collar is working?

Why does my shock collar not work?

Proper fit is crucial for the e-collar to have any impact on your dog. If BOTH contact points are not touching the dog’s skin, the dog will not perceive any sensation at all. This happens because the collar is on the dog too loose. If the e-collar is easily rotating around the dog’s neck, it is too loose.

How do I know if my PetSafe collar is working?

How do you reset a shock collar?

Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. You may need to hold both units 2-3 feet from each other before this occurs. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been reset and will begin flashing as normal.

How do I know if the shock collar is working?

Where do you put the PetSafe stubborn dog collar?

Make sure that the battery is not installed in the Receiver Collar. 2. Start with your pet standing comfortably (2A). 3. Place the Receiver Collar on your pet so that the “PetSafe®” logo is facing your pet’s chin. Center the Contact Points underneath your pet’s neck, touching the skin. Note: It is

What do you need to know about wireless PetSafe?

You temporarily define the Pet Area with Boundary Flags for a visual aid in training your pet. Your pet wears a Receiver Collar with Contact Points that touch his neck, and, once trained, is allowed to roam freely in the Pet Area.

What do you need to know about PetSafe harness?

Download fitting guide and browse FAQs for PetSafe® harnesses including Easy Walk®, Gentle Leader®, and Come With Me Kitty™ harnesses. Get troubleshooting, training, and answers to frequently asked questions for bark collars and ultrasonic bark deterrents. Learn how to train your pet using a remote trainer, clicker, or pet proofing barrier.

How often should you put a vibration collar on a dog?

• Avoid leaving the collar on the dog for more than 12 hours per day. • When possible reposition the collar on the pet’s neck every 1 to 2 hours. • Check the fit to prevent excessive pressure; follow the instructions in this manual. • Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.