How do you read Bryant error codes?

bryant furnace codes. Each of the following status codes is a two digit number with the first digit determined by number of flashes of the yellow led and the second digit determined by number of flashes of the green led.

How do you reset a high limit switch on a furnace?

How to Reset a Furnace Limit Switch

1. Locate your furnace’s heating duct.
2. Locate the white limit switch.
3. Look at each arm to identify the settings.
4. Identify the component (setting) located in between the two arms.
5. Set the temperature on the middle component to approximately 105 to 115 degrees Fahrenheit.

How do I reset my furnace heater?

How to Reset an Electric Furnace

1. First, turn off the power supply to the furnace by turning off the breaker in the circuit box.
2. Locate the reset button on the furnace and press it to reset the furnace.
3. If the button is popped up, press it down.
4. Return the cover to the blower compartment and turn the power on.

What does a solid red light mean on a Bryant furnace?

A solid red LED is a code. It means the board is normal and waiting for a heat call. Your blower is running and you aren’t getting a call for heat. Both those problems point to a thermostat problem.

Why is my furnace red light blinking?

When you see a flashing light, your furnace is sending you an error code. If you are looking at your furnace and do not see a red light at all when you know it should be on, that means your furnace is not receiving power. Check your circuit breaker box to see if you tripped the breaker for the furnace.

Where is the reset button on a limit switch?

Reset High Limit The High Limit Reset Button is located behind the gas valve.

Does a furnace have a reset button?

All furnaces are equipped with a reset button. They are generally red or yellow and are located inside the blower compartment. The reset button is a safety feature that will shut down the furnace when a problem is detected, often a hot or overheating furnace, before it trips the circuit breaker.

What to do when heater is not working?

Heater Not Working? 7 Troubleshooting Tips:

1. Check that your thermostat is set to “heat.”
2. Change the filter.
3. Make sure the gas is on.
4. Clear the chimney exhaust flue.
5. Clean away leaves and debris from exhaust vents.
6. Flush out the drain lines.
7. Check for blocked ducts restricting airflow.

What does 3 flashing lights mean on my furnace?

For example, three consecutive flashing lights on the Goodman furnace means there is an issue with the pressure switch circuitry. You must troubleshoot the switch to determine the reason why it is malfunctioning.

What does code 14 mean on a Bryant furnace?

Hello, I have a 15 year old Bryant 90 Plus furnace and I keep getting error code 14, which says it is “ignition lockout”. In the manual after reading error code 14, it says to refer to code 34, which is “ignition proving failure”.

Where do I find the model number on my Bryant gas furnace?

Gas or Oil Furnaces: Remove the front door and look at the upper-left side of the unit. You can find the model number listed on a “rating plate” sticker inside of the unit. If you have a different Bryant product, look for a “rating plate” sticker on the unit.

What does the flashing mean on a Bryant furnace?

I do not have that model of Bryant furnace. If it flashes with one flash followed by a pause, that’s when the low stage furnace is running normally. Two flashes with a pause mean the high stage of the furnace is engaged. That only helps me if I had a two stage furnace. And I’m getting error codes, not just flashing.

What causes Bryant error code 14 ignition lockout?

It usually causes a pressure switch tripping code if it is leaking. You may have a sticking gas valve or other problem and intermittent problems are the worst to diagnose. I usually stop/start it up to 24X in a row and odds are it fails once.