What does Ld mean on a washer machine?

long drain
If Ld (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation.

How do I reset my Whirlpool Calypso washer?

Your Calypso washer does not have a “reset” button. If the outlet works then the failure is likely the machine control board. You did not state if “PF” displays when you plugged the washer back in. It should have displayed “PF” for power failure when plugged back in.

How do I fix a Whirlpool washer error?

Unplug the washer or disconnect the power for one minute and reconnect it again. Reselect the cycle and press Start. If the code persists, Contact Us or Schedule Service Online so a qualified technician can diagnose the washer.

How do you reset a Whirlpool washing machine?

The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.

What does Ld mean on my Maytag washer?

Long Drain
mamajtown, Ld code is for Long Drain: this could indicate that the washing machine is taking longer than 5 minutes to drain out enough water to reset the water pressure switch.

What does Ld mean on a Speed Queen washer?

Speed Queen Ld – Long Drain.

What is the problem with Whirlpool washing machines?

The machines, branded as Hotpoint or Indesit, were sold for more than five years, but their door locking system can overheat creating the risk of fire. Owners face the prospect of doing without hot washes for months until products are fixed or replaced.

Do Whirlpool washers have a reset button?

How to Confirm You Have Reset Your Whirlpool Washing Machine. Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

Why is my Maytag washer not draining?

A clogged pump filter could also be responsible for a Maytag washer not draining. As the wash water drains, the filter screens out debris to prevent it from clogging the drain pump. If the filter becomes clogged, water can’t flow to the drain pump and exit the washer.

How do I reset my Maytag washer?

How to Reset a Maytag Washer

1. Press the “Power/Cancel” button.
2. Push the appropriate button to choose a new cycle.
3. Press “Start/Pause.” You have now reset your Maytag washer.

Are Speed Queen washers worth the extra money?

In our opinion, the Speed Queen washer is well worth the money. If you are tired of mold and mildew in your front load washer, this brand will give you reliable performance over years to come. Speed Queen is the only residential washing machine that can handle commercial grade load time after time.

When does a whirlpool Calypso washer lose power?

Home » Appliance Repair Help » Washing Machine Repair Help » Whirlpool Calypso Washing Machine Help » Whirlpool Calypso Fault Codes PF Power Failure PF flashes if the washer loses power during a running cycle. The washer does not flash PF when it is first plugged in.

What is the error code for LF long fill?

This does not generate an error code beep. LF Long Fill If the water fill time exceeds ten minutes, the water valves are turned off and LF is flashed. CE Communications Error If there is any breakdown in communication between the machine controller and the motor controller, CE flashes and the unit beeps once.

When does the thermistor fail on a dryer?

E1 or E2 Thermistor Failure The dryer will not operate if the exhaust temperature drops below 18 degrees F. or exceeds 250 degrees F. When the thermistor circuit is open (>50K ohms), the error code E1 flashes in the display. When the thermistor circuit is shorted (<500 ohms), the error code E2 flashes in the display.

What does PF flash when the washer loses power?

PF Power Failure PF flashes if the washer loses power during a running cycle. The washer does not flash PF when it is first plugged in. Press START to continue the cycle from the moment that power was lost -OR- Press STOP/CANCEL to clear the display and completely cancel the cycle. FL Flood Condition FL flashes if any overfill condition occurs.