What does E168 mean on my boiler?

Error code E168 could be telling you that a number of things are wrong with the boiler. The boiler will then have been reset, either automatically or by the user. Once the boiler starts up again it may not be able to detect the original fault and so will display E168 as a replacement for the previous code.

How do I fix error code 168?

The following steps should fix the error 168 issue:

1. Download PC Repair application See more information about Outbyte; uninstall instructions; EULA; Privacy Policy.
2. Install and launch the application.
3. Click the Scan Now button to detect issues and abnormalities.
4. Click the Repair All button to fix the issues.

Why does my Potterton boiler keep cutting out?

#5 Problem: Boiler Turning Off or Locking Out If your boiler keeps “locking out” with no obvious cause or error code being displayed, then this could be caused by a variety of different issues, including a faulty heat exchanger, faulty thermostat, or a faulty PCB.

What does E1 on boiler mean?

If the code E133 is displayed (‘E1′ then ’33’ flashing), this means either: The gas supply has been interrupted. If a pre payment gas meter is fitted, the credit on the gas meter has run out. Ignition has failed or a flame has not been detected.

What does a flashing red light mean on a Potterton boiler?

If the Status LED is showing continuous or flashing Red the boiler will need resetting. will attempt to re-light. Warning: If the LED is flashing Red rapidly the control is in remote diagnostic mode. The boiler will not operate in this mode and will need to be reset again.

How do you reset a Potterton gas boiler?

1. Reset. bar.
2. Off position. The boiler will not operate.
3. Central heating. and hot water. Both heating and. hot water will operate.
4. Hot water. Hot water will operate.
5. Reset. Hold for approximately. 5 seconds and release.

Why is my Potterton boiler flashing green?

When there is a call for heat the Status LED will flash Green and after several seconds the burner will light automatically. The Status LED will show continuous Green whilst water is being heated. If the Status LED is showing continuous or flashing Red the boiler will need resetting.

How do you reset a Potterton boiler?

What do you do when your boiler says E1 33?

If your boiler has shut down and is showing error code E133 or E28, then your condensate pipe may be frozen.

1. Switch your boiler off at the control panel, and turn off the electricity at the wall.
2. Find where the pipe is frozen, usually the most exposed part of the pipe.

What does E1 mean?

Why does Potterton Promax 24 show Code E168?

Now when trying to use UFH, code E168 shows again. Using the ‘good lady’, it looks to me like the UFH 2-port valve is not making the necessary circuit. The boiler (I assume) knows that it should be doing something but cannot achieve this. Hence, the E168 code shows.

Why does Potterton Combi he plus an error code E168?

It then locked out on Error Code E133, shown in the book as Interuption Of Gas Supply or Flame Failure. I turned the adjustment screw for the Gas/Air half a turn anti clockwise and it seemed to cure the problem for a while, but it has now started again. This morning it showed an Error Code of E168.

How to fix a Potterton Promax he plus boiler?

This problem is an ongoing matter with customer, engineers and Baxi/Potterton. The fault E168 is airbourne electrical interference. Remove all plugs from board and then reconnect plugs and reset. Remove (if any) magnets or anything magnetic from and around the boiler/casing.

What does the Potterton assure combi boiler code mean?

Promax Combi, System, and Store Error Codes Potterton Promax Ultra, Gold/Titanium Combi & System Boiler Error Codes Potterton Assure Combi and system Boiler Error Codes; Potterton Error Code E133 If you are seeing the error code E133 on your Potterton boiler, this means that your boiler condensate pipe is frozen.