Other

How do you turn off a Brocade switch?

by Rhyley Bryan

How do you turn off a Brocade switch?

To perform a system shutdown on a Brocade DCX: End-user is required to power-cycle the switch in order to restore operation. The system is going down for system halt NOW !!

How do you set up a Brocade fabric switch?

Connecting to the CLI

  1. Connect the workstation to the Ethernet network containing the HPE Synergy Frame Link Module.
  2. Connect to the switch using ssh or open a Telnet connection using the IP address set earlier.
  3. Enter the user name, using an administrative account.
  4. Enter the password.
  5. Verify the login was successful.

How do you reset a Brocade switch?

To reboot the CP and execute the normal power-on booting sequence, perform the following steps.

  1. Open the Switch Administration window as described in. Opening the Switch Administration window. on page 52.
  2. Click Reboot.
  3. On the Reboot Confirmation window, click Yes to continue.
  4. Click Apply.

What is the command used to find all WWNs logged in to the fabric?

The nsallshow command reports all of the fabric addresses in the fabric – but this is fairly useless as there doesn’t seem to be any other commands that use fabric addresses, or resolve them to WWNs!

How do I turn off my Brocade 300 Switch?

Procedure

  1. Connect to the switch and log in using an account assigned to the admin role.
  2. Enter the sysShutdown command.
  3. Enter y at the prompt.
  4. switch:admin> sysshutdown.
  5. This command will shutdown the operating systems on your switch.
  6. You are required to power-cycle the switch in order to restore operation.

How do you Zoning a Brocade switch?

How to create zones from CLI on a Brocade SAN Switch

  1. admin> switchshow.
  2. Note:Any devices that connect using NPIV use nsshow command to find the WWPN addresses logged in to the port.
  3. 2.Run the cfgshowcommand.
  4. admin> cfgshow.
  5. cfgshow will display the configuration and how the zoning is currently configured.

What is principal switch in Brocade?

A switch by default is the principal because it happened to have the lower wwn at the time of introducing the switches into a fabric. The Hardware, Software Compatibility List (HSCL) dictates that (for a Brocade in this example) the minimum version of firmware for Proxy (principal) switch is 5.3.

How do I remove zoning Brocade?

Brocade CLI – Zone Removal

  1. Putty to switch01(xx.xxx.xxx.xx)
  2. Backup existing zone configuration (This step is not mandatory but is a best practices always to backup zone configuration before making changes)
  3. Remove the zones from active zone configuration; Delete zones & alias from zone database.

How do I check logs on Brocade switch?

Windows

  1. Enter the IP or hostname of the Cisco or Brocade switch:
  2. Make sure logging is turned on for “All session output” and then save the resulting putty.log file to a location of your choice.
  3. For Brocade run the command supportshow.
  4. For Cisco run the command show tech-support details.

How do you check zoning on a Brocade switch?

If you cannot find the WWPN listing, you have to identify the WWPN manually from server / HBA and run “nodefindWWPN “ to verify that the WWPN is available on switch for zoning. cfgshow will display the configuration and how the zoning is currently configured.

How do you power cycle a Brocade switch?

How to power on and off Brocade SAN switches?

There are two commands: cfgsave: Backs up the current running configuration to the local switch. (Ensure that the configuration is the same after the switch restarts.) configupload: Backs up the local configuration file of the switch to the FTP server. 2. Powering Off the Switch You are not advised to power off the switch directly.

What are the commands for Brocade Fabric OS?

Brocade useful Fabric OS Commands. This is a list of useful Brocade switch commands that will help you for administration or management operation. These commands are useful for for Zoning, Show, Port, Time/Date, License, Banner, Password, SNMP, User Config, Firmware, and Miscellaneous.

What are the commands on a fabric switch?

These commands are useful for for Zoning, Show, Port, Time/Date, License, Banner, Password, SNMP, User Config, Firmware, and Miscellaneous. Displays the parameters of the switch. Ensure all switches in a fabric have the same parameters in order to communicate

How to disable high availability feature in brocade switch?

Disables the High Availability feature in the switch. Displays information about the status of the High Availability feature in the switch. Forces the failover mechanism so that the Standby Control Processor (CP)becomes the Active CP. Enables HA state synchronization. Disables the HA state synchronization.