How do I choose a garage door torsion spring?

Articles

1. Step 1: Determine the Wind Direction. Look at the end of the spring to determine the wind direction.
2. Step 2: Measure the Wire Size. Measure the length of ten or twenty coils of the spring that needs to be replaced, using inches.
3. Step 3: Measure the Inside Diameter.
4. Step 4: Measure the Overall Length.

Are all garage door torsion springs the same?

Most newer garage doors have two torsion springs, each of which must turn in a certain direction to lift and lower the door. However, when you look at the door from inside the garage, the left-wound spring will typically be on the right and vice versa.

Do I need one or two torsion springs?

Torsion spring systems can use one or two springs. As a rule of thumb, a single garage door takes one torsion spring. A double-wide garage door takes two springs. However, if you have an exceptionally heavy single door, you may need two torsion springs.

How many turns on a 7ft garage door spring?

If your door is 7ft high then we recommend starting off at 31 Quarter turns on each springs. If you have an 8ft door then start at 34 Quarter turns.

How do you balance a garage door with a torsion spring?

Loosen the tension on the spring 1/4 of a turn if the door is opening on its own. Use the torsion spring winding bar to rotate the adjusting collar 1/4 of a turn down. This will decrease the tension on the spring so the door doesn’t keep sliding up when you release it midway.

Can you manually open a garage door with a broken torsion spring?

As professionals in the industry, we advise you do not attempt to open your garage door if the spring is broken. Extension springs on either side of the door, along the rails, help counterbalance the weight of the door as it is raised or lowered. Torsion springs across the top of the door help do the heavy lifting.

Can garage door springs be too strong?

If your springs are too strong, and if you wind the springs the correct number of turns, the door will not stay on the floor when closed. It will usually not stay in the middle when opened halfway. However, it will stay up when opened fully.

How long do garage door torsion springs last?

How long do garage springs last, typically? The average garage door spring, if correctly installed, should last about 10,000 cycles of opening and closing. If you only go in and out of your garage once a day, that means you should expect a broken garage door spring around 14 years after the spring is first installed.

Which is better torsion or extension springs?

Torsion springs tend to be stronger and more durable than extension springs. And though they are more expensive, they last longer, between 15,000 and 20,000 cycles as opposed to 10,000 cycles with extension springs. They also offer greater balance and show more control when moving, not jerking as the door moves.

Should a garage door have one or two springs?

Extension Springs: 1 Spring vs 2 Springs Doors with extension springs should always have two springs. If one of your garage door springs breaks or is in poor condition, replace both springs. Replacing one spring just means the older spring will have to be replaced in a matter of time.

How many turns on a garage door tension spring?

A rule of thumb with springs is that four quarter turns equals a full revolution and the spring needs to be tightened a full revolution for every foot of door height (e.g. 7-1/2 foot door = 7 revolutions +2 (30 quarter turns).

How many times do you turn a garage door spring?

When you count 30 turns, you should know that you have completed the remaining five turns. This completes a total of seven spring turns, adequate for a standard garage door. In case of doubts on how many times you need to turn the spring, contact a technician for guidance.

How much to replace garage door torsion springs?

If you hire a professional to do the job, the costs to replace garage door springs will vary slightly depending on where you live. But generally, the midrange for parts and service to replace 1 or 2 torsion springs seems to be $200-$300.

How do you adjust a torsion spring garage door?

Adjusting Torsion Springs Close the garage door. Secure the door. Locate the winding cone. Loosen the set screws. Prepare to adjust the tension. Adjust the tension. Stretch the spring. Tighten the set screws. Repeat on the other side. Test your door. Lubricate the springs.

How do garage door torsion springs work?

Torsion springs are normally mounted horizontally above the opening of your garage door. When you pull the door down, cables attached to the bottom corners actually force the springs to wind up, in turn energizing the system. When you open the door, the springs then unwind and their energy transfers to the door,…