What does a Power Commander 3 do?

The Dynojet Power Commander plugs inline with your bike’s stock fuel injection system. It uses OEM (original equipment manufacturer) style connectors making installation easy and quick. The Power Commander III USB allows a full range of fuel adjustment, as much as +/- 100% over stock.

How do you program a Power Commander 3?

With the ignition off, hold down all three buttons on the Power Commander III unit. While still holding down the buttons, turn on the ignition and start the bike. Release the buttons. The light(s) should show up in the last place they were left, by default the center two lights.

Does a Power Commander increase horsepower?

The Power Commander is a tuning tool to adjust fuel, and on some models ignition timing. Just adding a Power Commander to a completely stock vehicle usually does not increase peak horsepower. It usually will improve drivability, throttle response, and mid-range horsepower and torque.

How do I connect my power commander 3 to my computer?

The Power Commander USB will instantly and automatically connect to the Power Commander Control Center software once it is installed. Simply “power up” the unit and connect the supplied USB cable to the computer and PCIII USB.

Does a Power Commander make a big difference?

Generally, the benefits of a power commander will work best with a full system exhaust (not a slip-on), as it creates more power and allows for a wider range of adjustments. If you’re more performance oriented, then a power commander may be worth the investment to get a smoother, more powerful ride.

Is a Power Commander plug and play?

The Power Commander can be sophisticated and simple at the same time depending on the end user. It can be a plug-and-play or custom mapped to your own specific riding requirements. And if you decide to change Harleys, you can take your Power Commander with you and install it in your new ride.

How do I adjust my power commander?

Hold down all three buttons on the face of the Power Commander unit and turn on the bike’s ignition. Release all the buttons once the engine is idling normally. The Power Commander manual recommends waiting approximately 20 seconds before making any adjustments.

How do I reset my power commander?

Power Commander III: How to Reset a PCIIIUSB

1. Connect it to the software and power it up using the 9-volt adapter.
2. Once you have communication established, go to the “Tools” menu and select “Environmental Options”.
3. A window will appear that has a black rectangular button at the bottom that reads “Reset Power Commander”.

Is the Power Commander worth it?

If you’re more performance oriented, then a power commander may be worth the investment to get a smoother, more powerful ride. If you’re pairing with a high end full system, like an Akrapovic Exhaust, you’ll see much better overall performance when paired with a PCV.

Does a Power Commander use more fuel?

A Power Commander will help you adjust the fuelling to not only crisp up the throttle response but also make the most of this improved intake and expulsion rate, to add in more fuel and air and help the engine produce more power and torque.

Do power commanders really work?

How do I know if my Power Commander is working?

The only way to tell if the PC-V is working or not, is to have the exhaust gases checked on a dyno utilizing an Exhaust Gas Analyzer. pipe and the cylinder head. to run lean and overheat, turning the pipes blue. Avoid long periods of idling.

What kind of connector does power Commander III use?

It uses OEM (original equipment manufacturer) style connectors making installation easy and quick. The Power Commander III USB allows a full range of fuel adjustment, as much as +/- 100% over stock. Adjustments can be made either with a Windows based computer or by using the face plate mounted button adjusters.

How do I power up my power commander?

Simply “power up” the unit and connect the supplied USB cable to the computer and PCIII USB. Onboard notes storage – The PCIII USB stores the notes from the map in the onboard memory.

What are the buttons on a power commander?

With the ignition off, hold down all three buttons on the Power Commander III unit. While still holding down the buttons, turn on the ignition and start the bike. Release the buttons. The light (s) should show up in the last place they were left, by default the center two lights.

How big is the power Commander III USB accelerator pump?

Software Description Size Power Commander III USB Control Center S 3.14 MB Power Commander III USB Reprogrammer Sof 389.84 kB Power Commander III USB Accelerator Pump 823.32 kB