How tight should trailer wheel nuts be?
How tight should trailer wheel nuts be?
The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off, about a quarter of a turn. The nut finger should be tight until the castle nut or cotter pin is used.
What is the torque spec for lug nuts?
New wheels should be re-torqued after the first 50 to 100 driving miles.
| Hardware Bolt or Stud Size | Typical Torque Range in Ft/Lbs | Minimum Number of Turns of Hardware Engagement |
|---|---|---|
| 14 x 1.25 mm | 85 – 90 | 9 |
| 7/16 in. | 70 – 80 | 9 |
| 1/2 in. | 75 – 85 | 8 |
| 9/16 in. | 135 – 145 | 8 |
Why is my trailer wheel wobbling?
A loose, worn or damaged wheel bearing is the most common cause of brakes that grab. If the wheels are loose or spin with a wobble, the bearings must be serviced or replaced. Check for noise – Have someone listen from both the driver’s side and the curbside as you tow your trailer past at about 25 mph.
How tight should a trailer spindle nut be?
Tighten the spindle nut finger tight (until snug) and then with channel-lock pliers or a crescent wrench, tighten the spindle nut another 1/4 turn or about 15 to 20 ft pounds of torque. Now turn the hub ten revolutions. This will fully seat the races.
How hot should a trailer hub get?
About 130-140 is too hot to touch and anything above that probably too hot for a wheel bearing. Compare it to your hot water temp at home. If you can’t touch the wheel then I would consider them too hot… warm to the touch is OK.
What kind of grease do you use for trailer bearings?
The best grease for travel trailer wheel bearings is the Lucas Oil 10301 Heavy Duty Grease. It lasts 4X longer than regular grease, is virtually waterproof, and is stable in all temperatures. It’s the ultimate grease for high-speed bearing.
Can you over tighten wheel bearings?
It’s possible to damage the wheel, rotor, and hub assembly. The wheel can come off if over-torquing the nuts/bolts is done. It happens, but it doesn’t happen a lot. The only way to tighten them is with a Torque wrench.
What should I torque trailer wheels to?
Lug Nut Torque for a Trailer Wheel 90-95 ft lbs of torque is probably about right for your trailer rims.
What happens if you dont torque lug nuts?
The improper use of tools, such as impact guns, can result in the same dangerous outcome or worse, as over-torqued lug nuts can cause permanent damage to them. The converse can also be detrimental. An under-torqued lug nut can loosen over time. This will redistribute the tension on the remaining lug nuts.
What is the lug nut torque on a trailer?
The standard torque on a Redline Trailer Wheel Lug Nut – 9/16 inch, part # 6-53, is 135 to 145 ft lbs. This is the torque range that is normally used.
What is the wheel lug nut torque?
Wheel Lug Torquing. (Lea en español) Proper wheel installation requires the wheel-attaching hardware (lug nuts or bolts) be tightened to the recommended torque specification for the vehicle make, model and year. Torque specifications are usually found in the vehicle’s owner’s manual.*. Proper torque requires using the correct tools, procedures and patterns.
What are the torque specifications for lug nuts?
Typical Lug Nut Torque Specifications. Lug Size Ft/Lbs Torque. 1/2″ 90-120 9/16″ 120-140 5/8″ 140-160. IMPORTANT NOTICE: As with all types of wheels retorque lug nuts after the first 25 miles & at 100 mile intervals until lug torque is maintained. How to Measure Bolt Patterns.
What size are trailer lug bolts?
There are common lug nut sizes found on trailers: 7/16, 1/2, 9/16, and 5/8 but the most common is 1/2 inch.