How do you adjust a state select water heater?

Pull the insulation from the cavity behind the covers to expose the thermostats. Insert a small flat-head screwdriver into the slot on the thermostat dial. Rotate the thermostat to your desired temperature. Make sure to adjust both thermostats if your Rheem water heater has two access covers.

Where should I set my water heater temperature?

Recommended Temperature Settings Water heaters are factory set at OSHA recommended levels, around 140 degrees. On the other hand, the EPA suggests turning the thermostat down to 120 to reduce power consumption, and a booster heater to reach sanitizing temperatures at select outlets.

What is the most economical temperature to set your water heater at?

Determine the Best Temperature for Your Water Heater The standard temperature for most water heaters is 140 degrees F, but the Department of EnergyLink opens in a new tab recommends turning down the temperature to 120 degrees to save energy.

Where is the reset button on a state select water heater?

Locate the large red button marked “Reset” at the center of your State water heater’s control circuit panel. Firmly press the “Reset” button to manually reset your water heater. Once your water heater has been reset, it may take between 12 and 24 hours for your water heater to resume normal operation.

Does turning up water heater make hot water last longer?

Turn up the thermostat on the hot water heater. One of the easiest ways to make a hot shower last longer is by using less hot water while it’s at a higher temperature. To do this, turn up the temperature on the thermostat that’s attached to the hot water heater tank. Be conscious of other hot water in your home.

Do electric hot water heaters have temperature control?

Most electric water heaters will have two thermostats, one upper and one lower, under the two control panels. For your water heater to work most effectively and efficiently, the two thermostats must be set at the same temperature. Some smaller units may only have one thermostat.

What temperature should I set my hot water heater ABC?

around 115 to 120 degrees Fahrenheit
Know the Ideal Setting: The best setting for gas water heaters is around 115 to 120 degrees Fahrenheit. Oftentimes, water heaters will have additional options to either lower or increase the temperature of the water inside. In the case of the video’s water heater, A, B and C each have an increase of about 10 degrees.

Is 150 too hot for water heater?

The recommended setting for household water heaters is not 150 degrees, but slightly less _ 140 degrees. Water temperatures higher than 140 degrees can burn the skin and are particularly dangerous for young children and the elderly. People with poor circulation can scald themselves without knowing it.

How long do state water heaters last?

about eight to 12 years
Based on the manufacturer’s suggested service life, the life expectancy of a water heater is about eight to 12 years. That varies with the location and design of the unit, quality of installation, maintenance schedule and water quality.

How do I reset my electric hot water heater?

Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.

Why do I only get 5 minutes of hot water?

So your water heater used to provide an adequate amount of hot water to keep you content. Well, if your hot water is suddenly turning lukewarm/cold after a few minutes, you most likely have a problem with your hot water heater. More specifically, you probably have a bad dip tube.

Where can I get a select electric water heater?

Enter your city and state or zip code to find a local installer. 1. Ballard Natural Gas Service, Inc. No Rebates. Change Location. The Select® Standard electric water heater is the reliable choice when you are looking to maximize your hot water output and is designed with environmentally-friendly insulation to reduce standby heat loss.

How do you adjust the temperature of an electric water heater?

Here’s general instructions for how to adjust an electric water heater’s thermostats (there are two, one at the bottom and one at the top). Consult the owner’s manual that came with your water heater for instructions for your particular model.

Where is the control panel on a state water heater?

Locate your State water heater’s control circuit panel. In most State water heater models, the control circuit panel looks like a rectangular metal box mounted to the side of the water heater. Use a screwdriver to remove the two screws that secure the door of the control circuit panel.

How to change location of Ballard electric hot water heater?

Change Location. Enter your city and state or zip code to find a local installer. 1. Ballard Natural Gas Service, Inc. No Rebates. Change Location.